User manual GIGABYTE GA-K8NE-RH

[. . . ] GA-K8NE-RH AMD Socket 754 Processor Motherboard User's Manual Rev. 2001 12ME-K8NER-2001R * The WEEE marking on the product indicates this product must not be disposed of with user's other household waste and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!* The WEEE marking applies only in European Union's member states. Motherboard GA-K8NE-RH Motherboard GA-K8NE-RH Apr. 19, 2006 Copyright © 2006 GIGA-BYTE TECHNOLOGY CO. , LTD. [. . . ] (Default value:4T) Set Write Recovery Time to 2 bus clock. (Default value) CAS# latency (Tcl) 1. 5/2/2. 5/3 Auto 5T~15T Min RAS# active time (Tras) RAS# to CAS# delay (Trcd) 2T/3T/4T/5T/6T/7T Row Precharge Time (Trp) Auto 2T/3T/4T/5T/6T/7T Row to Row delay (Trrd) Auto 2T/3T/4T Row cycle time (Trc) 7T~22T Row refresh cyc time (Trfc) 9T~24T Read-to-Write time (Trwt) Auto 1T/2T/3T/4T/5T Write Recovery Time (Twr) 2 bus clock 3 bus clock GA-K8NE-RH Motherboard - 44 - Write-to-Read Delay (Twtr) 1 bus clock 2 bus clock Set Write-to-Read Delay to 1 bus clock. (Default value) English Refresh Rate (Tref) Set the Refresh Rate. Read Preamble value 2~9. 5ns Set the Read Preamble value. (Default value: 5. 5ns) Set the Async Latency value (Default value: 7ns) Disable CPU Spread Spectrum. Set CPU Spread Spectrum to Center Spread. (Default value) Set PCI-E clock from 100Mhz to 150Mhz. Async Latency value 2~11ns CPU Spread Spectrum Disabled Center Spread PCIE Clock 100Mhz ~ 150Mhz Hammer Vid Control Supports adjustable Hammer Vide from 0. 825V to 1. 550V. (Default value: StartUp) Robust Graphics Booster Select the options can enhance the VGA graphics card bandwidth to get higher performance. Auto Set Robust Graphics Booster to Auto. (Default value) Fast Set Robust Graphics Booster to Fast. Turbo Set Robust Graphics Booster to Turbo. DDR voltage control Normal +0. 1V +0. 2V Supply DDR voltage as DDR required. (Default value) Increase DDR voltage +0. 1V. Increase DDR voltage +0. 2V. - 45 - BIOS Setup English 2-8 Top Performance CMOS Setup Utility-Copyright (C) 1984-2006 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management SetupTop Performance PnP/PCI Configurations Disabled. . . . . . . . . . . . . . . . . . . . . . . . . [ ] PC Health Status Enabled. . . . . . . . . . . . . . . . . . . . . . . . . . [ ] MB Intelligent Tweaker(M. I. T. ) Esc: Quit F8: Q-Flash Top Performance Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving : Select Item F10: Save & Exit Setup : Move ENTER: Accept ESC: AbortLoad Fail-Safe Defaults If you wish to maximize the performance of your system, enable "Top Performance. " Disabled Disable this function. (Default Value) Enabled Enable Top Performance function. "Top Performance" will increase H/W working speed. Different system configuration (both H/W component and OS) will effect the result. For example, the same H/W configuration might not run properly with Windows XP, but works smoothly with Windows NT. Therefore, if your system is not perform enough, the reliability or stability problem will appear sometimes, and we will recommend you disabling the option to avoid the problem as mentioned above. 2-9 Load Optimized Defaults CMOS Setup Utility-Copyright (C) 1984-2006 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status MB Intelligent Tweaker(M. I. T. ) ESC: Quit F8: Q-Flash Load Optimized Defaults : Select Item F10: Save & Exit Setup Top Performance Load Optimized Defaults Set Supervisor Password Set User Password Load Optimized Defaults (Y/N)?N Save & Exit Setup Exit Without Saving Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically detects. GA-K8NE-RH Motherboard - 46 - 2-10 Set Supervisor/User Password CMOS Setup Utility-Copyright (C) 1984-2006 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup Enter Password: PnP/PCI Configurations PC Health Status MB Intelligent Tweaker(M. I. T. ) ESC: Quit F8: Q-Flash : Select Item F10: Save & Exit Setup Change/Set/Disable Password Top Performance Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving English When you select this function, the following message will appear at the center of the screen to assist you in creating a password. Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the password. Type the password again and press <Enter>. You may also press <Esc> to abort the selection and not enter a password. [. . . ] Support : http://www. gigabyte. com. tw/Support/ServiceCenter. aspx Non-Tech. Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address : http://www. gigabyte. de Japan NIPPON GIGA-BYTE CORPORATION WEB address : http://www. gigabyte. co. jp Singapore GIGA-BYTE SINGAPORE PTE. Support : http://www. gigabyte. com. tw/Support/ServiceCenter. aspx Non-Tech. Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address: http://www. gigabyte. com. sg U. K. [. . . ]