User manual GIGABYTE GA-K8NSC-939

[. . . ] GA-K8NSC-939 AMD Socket 939 Processor Motherboard User's Manual Rev. 1003 12ME-K8NSC939-1003 Motherboard GA-K8NSC-939 Motherboard GA-K8NSC-939 Feb. 23, 2005 Copyright © 2006 GIGA-BYTE TECHNOLOGY CO. , LTD. The trademarks mentioned in the manual are legally registered to their respective companies. Notice The written content provided with this product is the property of Gigabyte. [. . . ] Supply HT-Link voltage as HT-Link required. (Default value) Increase HT-Link voltage +0. 1V. (Default value) Increase DDR voltage +0. 1V. Increase DDR voltage +0. 2V. HT-Link voltage control Normal +0. 1v +0. 2v +0. 3v DDR voltage control Normal +0. 1v +0. 2v Hammer Fid control This setup option will automatically assign by CPU detection. The option will display "Locked" and read only or will not show up if the CPU ratio is not changeable. The default is StartUp (set CPU clock ratio to default value). - 43 BIOS Setup English 2-8 Top Performance CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Top Performance Power Management Setup PnP/PCI Configurations Disabled. . . . . . . . . . . . . . . . . . . . . . . . . [ ] PC Health Status Enabled. . . . . . . . . . . . . . . . . . . . . . . . . . [ ] MB Intelligent Tweaker(M. I. T. ) ESC: Quit F8: Q-Flash : Move ESC: Abort Top Performance Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving : Select Item ENTER: Accept Setup F10: Save & Exit Load Optimized Defaults If you wish to maximize the performance of your system, set "Top Performance" as "Enabled". (Default Value) Enabled Enable Top Performance function. "Top Performance" will increase hardware working speed. Different system configuration (both hardware component and OS) will effect the result. For example, the same hardware configuration might not run properly with Windows XP, but works smoothly with Windows NT. Therefore, if your system is not perform enough, the reliability or stability problem will appear sometimes, and we will recommend you disabling the option to avoid the problem as mentioned above. 2-9 Load Optimized Defaults CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status MB Intelligent Tweaker(M. I. T. ) ESC: Quit F8: Q-Flash Load Optimized Defaults Top Performance Load Optimized Defaults Set Supervisor Password Set User Password Load Optimized Defaults (Y/N)?Exit Setup Save & N Exit Without Saving : Select Item F10: Save & Exit Setup Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically detects. GA-K8NSC-939 Motherboard - 44 - 2-10 Set Supervisor/User Password CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations Enter Password: PC Health Status MB Intelligent Tweaker(M. I. T. ) ESC: Quit F8: Q-Flash Top Performance Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving : Select Item F10: Save & Exit Setup Change/Set/Disable Password English When you select this function, the following message will appear at the center of the screen to assist you in creating a password. Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the password. Type the password again and press <Enter>. You may also press <Esc> to abort the selection and not enter a password. To disable password, just press <Enter> when you are prompted to enter password. A message "PASSWORD DISABLED" will appear to confirm the password being disabled. Once the password is disabled, the system will boot and you can enter Setup freely. The BIOS Setup program allows you to specify two separate passwords: SUPERVISOR PASSWORD and a USER PASSWORD. When disabled, anyone may access all BIOS Setup program function. When enabled, the Supervisor password is required for entering the BIOS Setup program and having full configuration fields, the User password is required to access only basic items. [. . . ] Support : http://tw. giga-byte. com/TechSupport/ServiceCenter. htm Non-Tech. Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address : http://www. gigabyte. de Japan NIPPON GIGA-BYTE CORPORATION WEB address : http://www. gigabyte. co. jp Singapore GIGA-BYTE SINGAPORE PTE. Support : http://tw. giga-byte. com/TechSupport/ServiceCenter. htm Non-Tech. Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address: http://www. gigabyte. com. sg U. K. [. . . ]