User manual GIGABYTE GA-M57SLI-S4

[. . . ] GA-M57SLI-S4 AMD AthlonTM 64 FX / AthlonTM 64 X2 Dual-Core / AMD AthlonTM 64 / SempronTM AM2 Processor Motherboard User's Manual Rev. 2002 12ME-M57SLI4R-2002R * The WEEE marking on the product indicates this product must not be disposed of with user's other household waste and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!* The WEEE marking applies only in European Union's member states. Motherboard GA-M57SLI-S4 Motherboard GA-M57SLI-S4 Apr. 11, 2007 Copyright © 2007 GIGA-BYTE TECHNOLOGY CO. , LTD. [. . . ] If no LAN cable is attached to the motherboard, the Status fields of all four pairs of wires will show Open and the Length fields show 0. 0m. English Onboard 1394 Enabled Disabled Enable onboard IEEE 1394 function. (Default value) Disable onboard IEEE 1394 function. Onboard LAN Boot ROM This function decide whether to invoke the boot ROM of the onboard LAN chip. (Default value) Onboard Serial Port 1 Auto 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 Disabled Disabled 378/IRQ7 278/IRQ5 3BC/IRQ7 SPP EPP ECP ECP+EPP BIOS will automatically setup the port 1 address. Enable onboard Serial port 1 and address is 3F8/IRQ4. (Default value) Enable onboard Serial port 1 and address is 2F8/IRQ3. Enable onboard Serial port 1 and address is 3E8/IRQ4. Enable onboard Serial port 1 and address is 2E8/IRQ3. Enable onboard LPT port and address is 378/IRQ7. (Default value) Enable onboard LPT port and address is 278/IRQ5. Enable onboard LPT port and address is 3BC/IRQ7. Using Parallel port as Standard Parallel Port. (Default value) Using Parallel port as Enhanced Parallel Port. Using Parallel port as Extended Capabilities Port. Using Parallel port as ECP and EPP mode. Onboard Parallel Port Parallel Port Mode GA-M57SLI-S4 Motherboard - 42 - ECP Mode Use DMA This item will become available when Parallel Port Mode set to ECP or ECP+EPP. (Default value) 1 Set ECP Mode Use DMA to 1. English On-Chip USB V1. 1+V2. 0 V1. 1 Disabled Enabled Disabled Enabled Disabled Enable USB 1. 1 and USB 2. 0 controllers. (Default value) Enable only USB 1. 1 controller Disable onchip USB support. (Default value) Enable USB mouse support. (Default value) USB Keyboard Support USB Mouse Support Legacy USB storage detect This option allows users to decide whether to detect USB storage devices, including USB flash drives and USB hard drives during POST. Enabled BIOS will scan all USB storage devices. (Default value) Disabled Disable this function. - 43 - BIOS Setup English 2-4 Power Management Setup CMOS Setup Utility-Copyright (C) 1984-2007 Award Software Power Management Setup [S1(POS)] [Instant-Off] [Enabled] [Enabled] [Disabled] [Disabled] Everyday 0:0:0 [Enabled] [Disabled] [Disabled] Enter [Soft-Off] Item Help Menu Level ACPI Suspend Type Soft-Off by Power button PME Event Wake Up Modem Ring On USB Resume from Suspend Power-On by Alarm x Day of Month Alarm x Time (hh:mm:ss) Alarm HPET Support (Note) Power On By Mouse Power On By Keyboard x KB Power ON Password AC BACK Function : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F6: Fail-Safe Defaults F10: Save ESC: Exit F1: General Help F7: Optimized Defaults ACPI Suspend Type S1(POS) S3(STR) Set ACPI suspend type to S1/POS(Power On Suspend). (Default value) Set ACPI suspend type to S3/STR(Suspend To RAM). Soft-Off by Power button Instant-Off Press power button then Power off instantly. Enter suspend if button is pressed less than 4 sec. PME Event Wake Up This feature requires an ATX power supply that provides at least 1A on the 5VSB lead. [. . . ] Question 5: Sometimes I hear different continuous beeps from computer after system boots up. Answer: The beep codes below may help you identify the possible computer problems. However, they are only for reference purposes. The situations might differ from case to case. [. . . ]