User manual GIGABYTE GA-M68MT-D3P

[. . . ] GA-M68MT-D3P GA-M68MT-S2P User's Manual Rev. 3001 12ME-M68MT2P-3001R AM3 socket motherboard for AMD PhenomTM II processor/ AMD AthlonTM II processor Motherboard GA-M68MT-D3P/GA-M68MT-S2P Motherboard GA-M68MT-D3P GA-M68MT-S2P Dec. 31, 2010 Copyright © 2010 GIGA-BYTE TECHNOLOGY CO. , LTD. The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE. [. . . ] Unganged Sets memory control mode to two single-channel. (Default) DDR3 Timing Items CAS# latency ManualallowsallDDR3Timingitemsbelowtobeconfigurable. Options are: Auto (default), 90ns, 110ns, 160ns, 300ns, 350ns. Options are: Auto (default), 90ns, 110ns, 160ns, 300ns, 350ns. - 21 BIOS Setup RAS to CAS R/W Delay Row Precharge Time Minimum RAS Active Time 1T/2T Command Timing TwTr Command Delay Trfc0 for DIMM1 Trfc1 for DIMM3 Write Recovery Time Precharge Time Row Cycle Time Options are: Auto (default), 4T~7T. Options are: Auto (default), 4T~7T. RAS to RAS Delay CKE Power Down Mode CKE Power Down Control DDR3 Voltage Control Determines whether to set the memory to power down mode when the CKE pin is closed. (Default: Disabled) Allows you to select a CKE power down mode. Options are per Channel (Default), per CS. CPU NB VID Control Allows you to set the memory voltage. Normal Supplies the memory voltage as required. (Default) +0. 1V ~ +0. 7V The adjustable range is from +0. 1V to +0. 7V. Note: Increasing memory voltage may result in damage to the memory or reduce the useful life of the memory. Allows you to set the CPU Northbridge VID voltage. Auto sets the CPU Northbridge VID voltage as required. The adjustable range is dependent on the CPU being installed. (Default: Normal) Note: Increasing CPU voltage may result in damage to your CPU or reduce the useful life of the CPU. The adjustable range is dependent on the CPU being installed. (Default: Normal) Note: Increasing CPU voltage may result in damage to your CPU or reduce the useful life of the CPU. Displays the normal operating voltage of your CPU. CPU Voltage Control Normal CPU Vcore 2-4 Standard CMOS Features CMOS Setup Utility-Copyright (C) 1984-2010 Award Software Standard CMOS Features Date (mm:dd:yy) Time (hh:mm:ss) Fri, Dec. 17 2010 22:31:24 [None] [None] [None] [None] [All, But Keyboard] 640K 1790M Item Help Menu Level IDE Channel 0 Master IDE Channel 1 Master IDE Channel 2 Master IDE Channel 3 Master Halt On Base Memory Extended Memory Enter: Select : Move F5: Previous Values +/-/PU/PD: Value F6: Fail-Safe Defaults F10: Save ESC: Exit F1: General Help F7: Optimized Defaults BIOS Setup - 22 - Date (mm:dd:yy) Time (hh:mm:ss) Sets the system date. Sets the system time. IDE Channel 0, 1, 2, 3 Master IDE HDD Auto-Detection, IDE Auto-Detection Press <Enter> to autodetect the parameters of the SATA device on this channel. IDE Channel 0, 1 Master, Extended IDE Drive ConfigureyourSATAdevicesbyusingoneofthethreemethodsbelow: ·Auto Lets the BIOS automatically detect SATA devices during the POST. (Default) ·None If no SATA devices are used, set this item to None so the system will skip the detection of the device during the POST for faster system startup. [. . . ] To enable RAID, go to the Serial-ATARAIDConfig sub-menu. Set NV SATA RAID function to Enabled to enable RAID control for each SATA connector. Then enable the SATA channels with hard drives that you want to use for RAID (for example, NV SATA 1 Primary RAID controls the SATA2_0 connector and NV SATA 1 Secondary RAID controls the SATA2_1 connector). The BIOS Setup options described in this section may differ from the exact settings for your motherboard. [. . . ]