User manual GIGABYTE GA-MF3

[. . . ] GA-MF3 AMD Socket AM2 Processor Motherboard User's Manual Rev. 1002 12ME-MF3-1002R * The WEEE marking on the product indicates this product must not be disposed of with user's other household waste and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!* The WEEE marking applies only in European Union's member states. Motherboard GA-MF3 Motherboard GA-MF3 Nov. 23, 2006 Copyright © 2006 GIGA-BYTE TECHNOLOGY CO. , LTD. [. . . ] When this function is enabled, CPU fan will run at different speed depending on CPU temperature. Users can adjust the fan speed with Easy Tune based on their requirements. (Default value) CPU/SYSTEM FAN Fail Warning CPU Smart FAN Control (Note) CPU Smart FAN Mode This option is available only when CPU Smart FAN Control is enabled. Auto BIOS autodetects the type of CPU fan you installed and sets the optimal CPU Smart FAN control mode for it. (Default value) Voltage Set to Voltage when you use a CPU fan with a 3-pin fan power cable. PWM Set to PWM when you use a CPU fan with a 4-pin fan power cable. (Note) Whether the CPU Smart FAN Control function is supported will depend on the CPU you install. - 42 - GA-MF3 Motherboard 2-7 MB Intelligent Tweaker(M. I. T. ) CMOS Setup Utility-Copyright (C) 1984-2006 Award Software CPU Frequency (MHz) AGP Clock (MHz) CPU Clock Ratio DDR2 voltage control AGP voltage Control CPU Voltage Control MB Intelligent Tweaker(M. I. T. ) [200] [66] [Auto] [Normal] [Normal] [Normal] Item Help Menu Level English : Move Enter: Select +/-/PU/PD: Value F5: Previous Values F10: Save ESC: Exit F7: Optimized Defaults F1: General Help Incorrectly using these features may result in system instability or corruption. Doing a overclock or overvoltage on CPU, chipsets and memory modules may result in damages or shortened life expectancy to these components. menu items are for power users only. CPU Frequency(MHz) 200~455 MHz Set CPU Frequency from 200 MHz to 455 MHz. Set AGP Frequency from 66 MHz to 100 MHz. AGP Clock(MHz) 66MHz ~ 100MHz CPU Clock Ratio The adjustable range is dependent on the CPU you install. (Default: Auto) DDR2 voltage Control Please note that by overclocking your system through the increase of the DDR2 voltage, damage to the memory may occur. Normal Supply DDR2 voltage as DDR2 requires. (Default value) +0. 1V ~ +0. 5V Increase DDR2 voltage by +0. 1V to +0. 5V. Incorrect using it may cause your system broken. For power End-User use only! AGP voltage Control Normal Supply AGP voltage as (G) MCH requires. (Default value) +0. 1V ~ +0. 3V Increase AGP voltage by +0. 1V to +0. 3V. Incorrect using it may cause your system broken. For power End-User use only! CPU Voltage Control Supports adjustable CPU Vcore. The adjustable range is dependent on CPUs. (Default value: Normal) Please note that by overclocking your system through the increase of the CPU voltage, damage to the CPU or decrease in the CPU life expectancy may occur. - 43 BIOS Setup English 2-8 Load Optimized Defaults CMOS Setup Utility-Copyright (C) 1984-2006 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Esc: Quit F8: Q-Flash Load Optimized Defaults MB Intelligent Tweaker(M. I. T. ) Load Optimized Defaults Set Supervisor Password Set User Password Load Optimized Defaults (Y/N)?N Setup Save & Exit Exit Without Saving : Select Item F10: Save & Exit Setup Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically detects. 2-9 Set Supervisor/User Password CMOS Setup Utility-Copyright (C) 1984-2006 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations Enter Password: PC Health Status Esc: Quit F8: Q-Flash MB Intelligent Tweaker(M. I. T. ) Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving : Select Item F10: Save & Exit Setup Change/Set/Disable Password When you select this function, the following message will appear at the center of the screen to assist you in creating a password. [. . . ] Question 5: Sometimes I hear different continuous beeps from computer after system boots up. Answer: The beep codes below may help you identify the possible computer problems. However, they are only for reference purposes. The situations might differ from case to case. [. . . ]