User manual GIGABYTE GA-X99-UD5 WIFI ANNEXE 1

[. . . ] GA-X99-UD5 WIFI User's Manual Rev. 1101 12ME-X99U5WF-1101R Motherboard GA-X99-UD5 WIFI Motherboard GA-X99-UD5 WIFI Aug. 15, 2014 Wireless Module Country Approvals: See the latest safety and regulatory documents at GIGABYTE's website. Copyright © 2014 GIGA-BYTE TECHNOLOGY CO. , LTD. The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE. [. . . ] (Default: Disabled) Allows you to select the type of the device connected to the SATA port. (Default: Hard Disk Drive) `` SATA Mode options && SATA Port 0/1/2/3/4/5 && Hot plug && SATA Device Type - 61 - BIOS Setup && XHCI Mode && Audio Controller Allows you to determine the operating mode for the xHCI controller in OS. Smart Auto This mode is available only when the BIOS supports the xHCI controller in the pre-boot  environment. This mode is similar to Auto, but it adds the capability to route the ports to xHCI or EHCI according to setting used in previous boots (for non-G3 boot) in the pre-boot environment. This allows the use of USB 3. 0 devices prior to OS boot. xHCI controller enabling and rerouting should follow the steps in Auto, when previous boot routs ports to EHCI. Note: This is the recommended mode when BIOS has xHCI preboot support. (Default) Auto   BIOS routes the sharable ports to EHCI controller. Then it uses ACPI protocols to provide an option to enable the xHCI controller and reroute the sharable ports. Note: This is the recommended mode when BIOS does NOT have xHCI pre-boot support. Enabled All shared ports are eventually routed to the xHCI controller during the BIOS boot process.  If BIOS does not have pre-boot support for the xHCI controller, it should initially route the sharable ports to the EHCI controller and then prior to OS boot it should route the ports to xHCI controller. Note: OS has to provide support for the xHCI controller in this mode. If the OS does not provide support, all sharable ports won't work. Disabled  USB 3. 0 ports are routed to the EHCI controller and the xHCI controller is turned  The off. All USB 3. 0 devices function as High Speed devices regardless of xHCI software support/availability. Manual Allows you to determine whether to rout the USB 3. 0 ports to the xHCI or EHCI controller  before booting to OS, and also provides you with options to manually rout each USB 3. 0/2. 0 port to xHCI or EHCI. Enables or disables the onboard audio function. (Default: Auto) Allows you to configure the ASPM mode for Chipset DMI link. (Default: Enabled) && PCH DMI ASPM && PCH Internal LAN (LAN2) && Wake on LAN Enables or disables the onboard LAN function. (Default: Enabled) If you wish to install a 3rd party add-in network card instead of using the onboard LAN, set this item to Disabled. Enables or disables the wake on LAN function. [. . . ] 4, et CNR-210, No 4 (Dec 2000) et No 5 (Nov 2001). « Pour empêcher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit être utilisé a l'intérieur et devrait être placé loin des fenêtres afin de fournir un écran de blindage maximal. Si le matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence. » European Community Directive R&TTE Directive Compliance Statement: This equipment complies with all the requirements and other relevant provisions of Directive 1999/5/EC of the European Parliament and the Council of March 9, 1999 on Radio Equipment and Telecommunication Terminal Equipment (R&TTE). [. . . ]