User manual GIGABYTE GO-B5232A

[. . . ] No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission. In order to assist in the use of this product, carefully read the User's Manual. For product-related information, check on our website at: http://www. gigabyte. com Identifying Your Motherboard Revision The revision number on your motherboard looks like this: "REV: X. X. " For example, "REV: 1. 0" means the revision of the motherboard is 1. 0. Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information. [. . . ] Important: It is highly recommended that the CPU frequency be set in accordance with the CPU specifications. Allows you to manually set the PCIe clock frequency. The adjustable range is from 90 MHz to 150 MHz. Auto sets the PCIe clock frequency to standard 100 MHz. (Default: Auto) ******** DRAM Performance Control ******** Performance Enhance (G)MCH Frequency Latch Allows the system to operate at three different performance levels. Standard Lets the system operate at its basic performance level. (Default) Turbo Lets the system operate at its good performance level. Extreme Lets the system operate at its best performance level. System Memory Multiplier (SPD) Memory Frequency (Mhz) Allows you to fix the chipset frequency at system bootup. Options for adjusting memory multiplier below may differ according to the fixed frequency. Options are: Auto (default), 200MHz, 266MHz, 333MHz. Allows you to set the system memory multiplier. >>> DRAM CPU Termination DRAM Voltage The default is Auto. The default is Auto. 2-4 Standard CMOS Features CMOS Setup Utility-Copyright (C) 1984-2011 Award Software Standard CMOS Features Date (mm:dd:yy) Time (hh:mm:ss) Wed, Dec 7 2011 22:31:24 [None] [None] [None] [None] [None] [None] [All, But Keyboard] 640K 988M 990M +/-/PU/PD: Value F6: Fail-Safe Defaults F10: Save ESC: Exit F1: General Help F7: Optimized Defaults Item Help Menu Level IDE Channel 0 Master IDE Channel 0 Slave IDE Channel 2 Master IDE Channel 2 Slave IDE Channel 3 Master IDE Channel 3 Slave Halt On Base Memory Extended Memory Total Memory Enter: Select : Move F5: Previous Values - 26 - Date (mm:dd:yy) Time (hh:mm:ss) Sets the system date. Sets the system time. IDE Channel 0, 2, 3 Master/Slave Halt On IDE Channel 0 Master/Slave, Extended IDE Drive Configure your IDE/SATA devices by using one of the three methods below: · None If no IDE/SATA devices are used, set this item to None so the system will skip the detection of the device during the POST for faster system startup. · Auto Lets the BIOS automatically detect IDE/SATA devices during the POST. (Default) · Manual Allows you to manually enter the specifications of the hard drive when the hard drive access mode is set to CHS. (For IDE Channel 0 Master/Slave only. ) Access Mode Sets the hard drive access mode. (Default: Auto) The following fields display your hard drive specifications. If you wish to enter the parameters manually, refer to the information on the hard drive. Capacity Approximate capacity of the currently installed hard drive. Allows you to determine whether the system will stop for an error during the POST. Options are: "All Errors, " "No Errors, " "All, But Keyboard, " (Default) "All, But Diskette, " "All, But Disk/Key". These fields are read-only and are determined by the BIOS POST. Memory 2-5 Advanced BIOS Features CMOS Setup Utility-Copyright (C) 1984-2011 Award Software Advanced BIOS Features [Press Enter] [Disabled] [Auto] [Hard Disk] [CDROM] [USB-FDD] [Setup] [Enabled] [Enabled] [Disabled] [Enabled] [Enabled] [Disabled] [Enabled] [Enabled] [Enabled] [0] [Disabled] +/-/PU/PD: Value F6: Fail-Safe Defaults F10: Save Item Help Menu Level Hard Disk Boot Priority Quick Boot EFI CD/DVD Boot Option First Boot Device Second Boot Device Third Boot Device Password Check HDD S. M. A. R. T. [. . . ] - 35 - 2-14 Save & Exit Setup CMOS Setup Utility-Copyright (C) 1984-2011 Award Software MB Intelligent Tweaker(M. I. T. ) PC Health Status Standard CMOS Features Load Fail-Safe Defaults Advanced BIOS Features Load Save to CMOS and EXIT (Y/N)?Y Optimized Defaults Advanced Chipset Features Set Supervisor Password Integrated Peripherals Set User Password Power Management Setup Save & Exit Setup PnP/PCIConfigurations Exit Without Saving : Select Item F10: Save & Exit Setup Save Data to CMOS F11: Save CMOS to BIOS F12: Load CMOS from BIOS ESC: Quit F8: Q-Flash Press <Enter> on this item and press the <Y> key. This saves the changes to the CMOS and exits the BIOS Setup program. Press <N> or <Esc> to return to the BIOS Setup Main Menu. 2-15 Exit Without Saving CMOS Setup Utility-Copyright (C) 1984-2011 Award Software MB Intelligent Tweaker(M. I. T. ) Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCIConfigurations PC Health Status Load Fail-Safe Defaults Quit Without Saving (Y/N)?Load Optimized Defaults N Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving : Select Item F10: Save & Exit Setup Abandon all Data F11: Save CMOS to BIOS F12: Load CMOS from BIOS ESC: Quit F8: Q-Flash Press <Enter> on this item and press the <Y> key. [. . . ]