User manual GIGABYTE GO-C5200A

[. . . ] No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission. Documentation Classifications In order to assist in the use of this product, GIGABYTE provides the following types of documentations: For quick set-up of the product, read the Quick Installation Guide included with the product. For detailed product information, carefully read the User's Manual. For product-related information, check on our website at: http://www. gigabyte. com Identifying Your Motherboard Revision The revision number on your motherboard looks like this: "REV: X. X. " For example, "REV: 1. 0" means the revision of the motherboard is 1. 0. Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information. Example: Table of Contents GO-C5200A Motherboard Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 GO-C5200A Motherboard Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Chapter 1 Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1-1 1-2 1-3 1-4 1-5 1-6 1-7 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 2-13 Installation Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] DCTs Addr/Cmd Timing** ** & Addr/Cmd Setup Time & Addr/Cmd Fine Delay & CS/ODT Setup Time & CS/ODT Fine Delay & CKE Setup Time & CKE Fine Delay Options are: Auto (default), 1/2T, 1T. Options are: Auto (default), 0/64~31/64. Options are: Auto (default), 0/64~31/64. Options are: Auto (default), 0/64~31/64. & Channel Interleaving Enables or disables memory channel interleaving. Enabled allows the system to simultaneously access different channels of the memory to increase memory performance and stability. (Default: Enabled) - 25 - & Bank Interleaving Enables or disables memory bank interleaving. Enabled allows the system to simultaneously access different banks of the memory to increase memory performance and stability. (Default: Enabled) Enables or disables memory DQS training each time the system restarts. (Default: Skip DQS) & DQS Training Control & CKE Power Down Mode Determines whether to set the memory to power down mode when the CKE pin is closed. (Default: Disabled) Determines whether to enable memory clock tri-stating in CPU C3 or Alt VID mode. (Default: Disabled) & Memclock tri-stating ******** System Voltage Optimized ******** & System Voltage Control Determines whether to manually set the system voltages. Access Mode Sets the hard drive access mode. Capacity Approximate capacity of the currently installed hard drive. Allows you to determine whether the system will stop for an error during the POST. Options are: "All Errors, " "No Errors, " "All, But Keyboard". (Default) These fields are read-only and are determined by the BIOS POST. & IDE Channel 2 Master/Slave & Halt On & Memory - 27 - 2-5 Advanced BIOS Features CMOS Setup Utility-Copyright (C) 1984-2011 Award Software Advanced BIOS Features Load Line Control AMD C1E Support Virtualization AMD K8 Cool&Quiet control CPU Unlock (Note) CPU core Control (Note) CPU core 0 (Note) CPU core 1 (Note) CPU core 2/3/4/5 (Note) Hard Disk Boot Priority EFI CD/DVD Boot Option First Boot Device Second Boot Device Third Boot Device Password Check HDD S. M. A. R. T. Capability Away Mode Full Screen LOGO Show IOMMU support Init Display First [Auto] [Auto] [Disabled] [Auto] [Disabled] [Auto] Enabled Enabled Enabled [Press Enter] [Auto] [Hard Disk] [CDROM] [USB-FDD] [Setup] [Disabled] [Disabled] [Enabled] [Disabled] [PCI Slot] +/-/PU/PD: Value F6: Fail-Safe Defaults F10: Save Item Help Menu Level x x x Enter: Select : Move F5: Previous Values ESC: Exit F1: General Help F7: Optimized Defaults & Load Line Control & AMD C1E Support Enables or disables Load Line control. This item allows you to adjust Vdroop at different levels. Enabling Load Line control may keep the CPU voltage more constant under light and heavy CPU load. Auto lets the BIOS automatically configure this setting. (Default: Auto) Enables or disables the C1E CPU power-saving function in system halt state. When enabled, the power consumption will be reduced during system halt state. [. . . ] Press <Esc> to return to Main Menu and press <Esc> again if you want to exit the RAID BIOS utility. Making a SATA RAID Driver Diskette Before installing Windows XP, connect a USB floppy disk drive to your computer first because you need to install the SATA RAID/AHCI driver from a floppy disk that contains the driver during the OS installation. To copy the RAID driver for Windows XP, copy all files in the \BootDrv\SBxxx\x86 folder in the motherboard driver disk to your floppy disk. (To install Windows 64-bit, copy the files in the x64 folder. ) Installing the SATA RAID Driver and Operating System A. Installing Windows XP Restart your system to boot from the Windows XP setup disk and press <F6> as soon as you see the message "Press F6 if you need to install a 3rd party SCSI or RAID driver. " Insert the floppy disk containing the SATA RAID driver. [. . . ]