User manual GIGABYTE GO-D1600F

[. . . ] No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission. In order to assist in the use of this product, carefully read the User's Manual. For product-related information, check on our website at: http://www. gigabyte. com Identifying Your Motherboard Revision The revision number on your motherboard looks like this: "REV: X. X. " For example, "REV: 1. 0" means the revision of the motherboard is 1. 0. Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information. [. . . ] Auto BIOS will automatically adjust the HT Link Width. (Default) 8 bit Sets HT Link Width to 8 bit. Allows you to manually set the frequency for the HT Link between the CPU and chipset. Auto BIOS will automatically adjust the HT Link Frequency. (Default) x1~x13 Sets HT Link Frequency to x1~x13 (200 MHz~2. 6 GHz). PCIE Clock(MHz) HT Link Width HT Link Frequency Set Memory Clock Determines whether to manually set the memory clock. Auto lets BIOS automatically set the memory clock as required. Manual allows the memory clock control item below to be configurable. (Default: Auto) This item is present only when you install a CPU that supports this feature. - 23 - (Note) Memory Clock This option is configurable only when Set Memory Clock is set to Manual. Options are: X3. 33, X4. 00, X5. 33, X6. 66, X8. 00, and X9. 33. DRAMConfiguration CMOS Setup Utility-Copyright (C) 1984-2011 Award Software DRAMConfiguration [Unganged] [Auto] Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto [Enabled] [Enabled] [Skip DQS] [Disabled] +/-/PU/PD: Value F6: Fail-Safe Defaults F10: Save ESC: Exit F1: General Help F7: Optimized Defaults SPD -9T 9T 9T 24T 5T 110ns -10T 5T 33T 4T Auto -6T 6T 6T 15T 4T 110ns -10T 5T 33T 4T Item Help Menu Level x x x x x x x x x x x x DCTs Mode DDR3 Timing Items 1T/2T Command Timing CAS# latency RAS to CAS R/W Delay Row Precharge Time Minimum RAS Active Time TwTr Command Delay Trfc0 for DIMM1 Trfc1 for DIMM2 Write Recovery Time Precharge Time Row Cycle Time RAS to RAS Delay Channel Interleaving Bank Interleaving DQS Training Control Memclock tri-stating Enter: Select : Move F5: Previous Values DCTs Mode DDR3 Timing Items Allows you to set memory control mode. Ganged Sets memory control mode to single dual-channel. Note: Increasing memory voltage may result in damage to the memory. The adjustable range is dependent on the CPU being installed. (Default: Normal) Note: Increasing CPU voltage may result in damage to your CPU or reduce the useful life of the CPU. - 25 - CPU NB VID Control Normal CPU Vcore Allows you to set the CPU North Bridge VID voltage. Auto sets the CPU North Bridge VID voltage as required. The adjustable range is dependent on the CPU being installed. (Default: Normal) Note: Increasing CPU voltage may result in damage to your CPU or reduce the useful life of the CPU. Displays the normal operating voltage of your CPU. Displays the normal operating voltage of your CPU North Bridge. Normal CPU Vcore NB 2-4 Standard CMOS Features CMOS Setup Utility-Copyright (C) 1984-2011 Award Software Standard CMOS Features Date (mm:dd:yy) Time (hh:mm:ss) Mon, Dec 26 2011 22:31:24 [None] [None] [None] [None] [None] [None] [All, But Keyboard] 640K 766M +/-/PU/PD: Value F6: Fail-Safe Defaults F10: Save ESC: Exit F1: General Help F7: Optimized Defaults Item Help Menu Level IDE Channel 0 Master IDE Channel 0 Slave IDE Channel 1 Master IDE Channel 1 Slave IDE Channel 2 Master IDE Channel 2 Slave Halt On Base Memory Extended Memory Enter: Select : Move F5: Previous Values Date (mm:dd:yy) Time (hh:mm:ss) Sets the system date. Sets the system time. IDE Channel 0, 1 Master/Slave IDE Channel 2 Master/Slave IDE Channel 0, 1 Master/Slave Configure your SATA devices by using one of the three methods below: · None If no SATA devices are used, set this item to None so the system will skip the detection of the device during the POST for faster system startup. · Auto Lets the BIOS automatically detect SATA devices during the POST. (Default) · Manual Allows you to manually enter the specifications of the hard drive when the hard drive access mode is set to CHS. [. . . ] Press <Ctrl>+<Y> to set the capacity of the RAID array or press other keys to set the array to its maximum capacity. Press Ctrl-Y to Modify Array Capacity or press any other key to use maximum capacity. . . Figure 2 7. After the creation is complete, the screen will return to DefineLDMenu where you will see the newlycreated array. Press <Esc> to return to Main Menu and press <Esc> again if you want to exit the RAID BIOS utility. - 38 - Making a SATA RAID/AHCI Driver Diskette Before installing Windows XP, connect a USB floppy disk drive to your computer first because you need to install the SATA RAID/AHCI driver from a floppy disk that contains the driver during the OS installation. To copy the RAID/AHCI driver for Windows XP, copy all files in the \BootDrv\SBxxx folder in the motherboard driver disk to your floppy disk. Installing the SATA RAID/AHCI Driver and Operating System A. [. . . ]