User manual GIGABYTE GS-R1271-RH

[. . . ] GS-R1271-RH 1U Rack Mount Server System Installation Guide Dual Intel® Xeon LGA771 Processor Serverboard Rev. 1. 0 GS-R1271-RH Rack Mount Server Table of Content Safety, Care and Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Contents Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Step 4 Reverse step 1 to 3 to reinstall riser bracket into the system module. 3 1 2 3 15 Hardware Installation Process Step 2-6: Hard Disk Drive Installation Step 1 Press the release button. Step 2 Pull the blank out of the drive bay. Step 5 Slide the blank into the bay until it locks into place. Connect cable and power. 1 2 3 4 4 4 4 16 Hardware Installation Process Step 2-7: FAN Duct Removal and Installation Step 1 Pull up the cabled and align the fan duct with the guiding groove. Push down the fan duct into system ntil the its firmly seats. Step 2 Please push the cables into the gap between fan duct and power supply. 1 Guiding groove 17 GS-R1271-RH Rack Mount Server Chapter 3 Appearance of GS-R1271-RH 3-1: Front View of GS-R1271-RH Standard DVD-COMBO Hot-Swap SATA HDDs USB connectors VGA port Front panel switch and LEDs 18 System Appearance 3-2: Rear View of GS-R1271-RH Power Mouse connector Keyboard connector COM port VGA port USB connectors RJ45 LAN ports Low-profile riser slot Full-height riser slot 19 GS-R1271-RH Rack Mount Server 3-3: Switch and LED Indicators Introduction LAN1/2 LED 1 ID LED ID Switch ID NMI Power Button ID 2 HDD NMI Error Name Power Color Green Green -Green -Blue Condition On Blink Off Blink Off On Off On Off Description Power On Sleep (S1) Power Off (S4/S5) Hard Disk Drive Access No Access and No HDD Fault Unti selected for identification No identification IPMI shows the event log. No event log in IPMI HDD ID (Identification) -Yellow Error - 20 System Appearance 3-4: LAN LED Description Name LAN Color Green - Condition ON BLINK OFF ON BLINK ON BLINK OFF Description LAN Link / no Access LAN Access Idle 1Gbps connection Port identification with 1Gbps connection 100Mbps connection Port identification with 10 or 100Mbps connection 10Mbps connection Link/Activity Green GbE LAN Yellow Speed Yellow Green Green - 21 GS-R1271-RH Rack Mount Server 3-5: Connector Icon Description Suggest Icon Description Keyboard Mouse VGA COM LAN USB 22 Motherboard Layout Chapter 4 Motherboard Jumper Setting 4-1: GA-7NCSV1-RH Motherboard Jumper Setting 2 3 4 5 1 8 6 7 1. System Identify 23 GS-R1271-RH Rack Mount Server 1. CLR_CMOS ( (Clear CMOS jumper) You may clear the CMOS data to its default values by this jumper. Default value doesn't include the "Shunter" to prevent from improper use this jumper. To clear CMOS, temporarily short 2-3 pin. 1 1 1-2 Close: Normal operation (Default setting) 2-3 Close: Clear CMOS 2. PWR_JP1 (Front panel USB1 power source selection jumper) 1 1 1-2 Close: 5V_AUX 2-3 Close: 5V 3. PILOT_DIS (Pilot II BMC Function Enable/Disable jumper) 1 1 1-2 Close: Enable Pilot II BMC function 2-3 Close: Disable Pilot II BMC function 4. BMC_SEL1 (BMC Firmware area selection) 1 1 1-2 Close: Select BMC firmware in bank0 2-3 Close: Select BMC firmware in bank1 5. SPI_WP1 (SPI BIOS write protection Disable/Enable jumper) 1 1 1-2 Close: Select BMC firmware in bank0 2-3 Close: Select BMC firmware in bank1 24 Jumper Setting 6. RECOVERY1 (BIOS recovery jumper) 1 1 1-2 Close: Normal operation(Default setting) 2-3 Close: Enable BIOS Recovery function. 7. PASSWORD1 (Skip password jumper) 1 1 1-2 Close: Normal operation. (Default setting) 2-3 Close: Clear Supervisor Password in BIOS setup menu. 8. Ssystem Identify (System Identify Enable/Disable jumper) 1 1 1-2 Close: Enable System Identify function. (Default setting) 2-3 Close: Disable System Identify function. 25 BIOS Setup Chapter 5 BIOS Setup BIOS (Basic Input and Output System) includes a CMOS SETUP utility which allows user to configure required settings or to activate certain system features. The CMOS SETUP saves the configuration in the CMOS SRAM of the motherboard. When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS SRAM. ENTERINGSETUP When the power is turned on, press the <F2> button during the BIOS POST (Power-On Self Test) will take you to the CMOS SETUP screen. [. . . ] (Default setting) Address obtained by BMC running static address. 47 IP Address Source DHCP Static GS-R1271-RH Rack Mount Server Console Redirection Figure 5-2: Console Redirection COM Port Address If this option is set to enabled, it will use a port on the motherboard to run console redirection function. Serial Port B Disabled Use Serial Port B as the COM port address. (Default setting) Baud Rate This option allows user to set the specified baud rate. Options 300, 1200, 2400, 9600, 19. 2K, 38. 4K, 57. 6K, 115. 2K. Console Type This option allows user to select the specified terminal type. [. . . ]