User manual GIGABYTE GS-R227E-RH

[. . . ] GS-R227E-RH 2U Rack Mount Server System Installation Guide Dual Intel® Xeon LGA771 Processor Serverboard Rev. 1. 0 GS-R227E-RH Rack Mount Server Table of Content Safety, Care and Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Contents Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (See illustrated below) Step 3 Lift the riser bracket slightly, then pull it out from the server chassis. Align the expansion card with the guiding groove. Slide the expansion card into the slot until the card firmly seats. Step 4 Align the riser bracket to the system module. 22 1 1 2 2 3 15 Hardware Installation Process Step 2-6: Hard Disk Drive Installation Step 1 Press the release button. Step 2 Pull the blank out of the drive bay. Step 5 Slide the blank into the bay until it locks into place. Connect cable and power. 1 2 3 4 4 16 Hardware Installation Process Step 2-7: FAN Duct Removal and Installation Step 1 Align the fan duct with the guiding groove. Push down the fan duct into system ntil the its firmly seats. 1 Guiding groove 17 GS-R227E-RH Rack Mount Server Chapter 3 Appearance of GS-R227E-RH 3-1: Front View of GS-R227E-RH DVD-COMBO Hot-Swap SATA HDDs USB connectors Front panel switch and LEDs 18 System Appearance 3-2: Rear View of GS-R227E-RH Power Mouse connector Keyboard connector COM port VGA port USB connectors RJ45 LAN ports Low-profile riser slot Full-Height riser slot 19 GS-R227E-RH Rack Mount Server 3-3: Switch and LED Indicators Introduction Buzzer Stop ID Switch Reset RESET BUZZER STOP Power Button Name Power ID Color Green Green -Blue Condition On Blink Off On Off Description Power On Sleep (S1) Power Off (S4/S5) Unti selected for identification No identification (Identification) -- 20 System Appearance 3-4: LAN LED Description Name Color LAN Green Link/Activity Green GbE LAN Yellow Speed Yellow Green Green - Condition ON BLINK OFF ON BLINK ON BLINK OFF Description LAN Link / no Access LAN Access Idle 1Gbps connection Port identification with 1Gbps connection 100Mbps connection Port identification with 10 or 100Mbps connection 10Mbps connection 21 GS-R227E-RH Rack Mount Server 3-5: Connector Icon Description Suggest Icon Description Keyboard Mouse VGA COM LAN USB 22 Motherboard Layout Chapter 4 Motherboard Jumper Setting 4-1: GA-7BESV1-RH Motherboard Jumpper Setting JP_REC1 CLR_CMOS1 PAS_DIS1 23 GS-R227E-RH Rack Mount Server 1. CLR_CMOS1 ( (Clear CMOS jumper) You may clear the CMOS data to its default values by this jumper. Default value doesn't include the "Shunter" to prevent from improper use this jumper. To clear CMOS, temporarily short 2-3 pin. 1 1 1-2 Close: Normal operation (Default setting) 2-3 Close: Clear CMOS 2. JP_REC1 (BIOS Revocery jumper) Open: Normal operation(Default setting) Close: Enable BIOS Recovery function. 3. PAS_DIS1 (Skip password jumper) 1 1 1-2 Close: Normal operation (Default setting) 2-3 Close: Skip supervisor password. 24 BIOS Setup Chapter 5 BIOS Setup BIOS (Basic Input and Output System) includes a CMOS SETUP utility which allows user to configure required settings or to activate certain system features. The CMOS SETUP saves the configuration in the CMOS SRAM of the motherboard. When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS SRAM. ENTERINGSETUP When the power is turned on, press the <F2> button during the BIOS POST (Power-On Self Test) will take you to the CMOS SETUP screen. You can enter the BIOS setup screen by pressing "Ctrl + F1". CONTROLKEYS <> <> < < > > Move to previous item Move to next item Move to the item in the left hand Move to the item in the right hand Main Menu - Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu - Exit current page and return to Main Menu <+/PgUp> Increase the numeric value or make changes <-/PgDn> <F1> <F2> <F3> <F4> <F6> <F7> <F8> <F9> <F10> Decrease the numeric value or make changes General help, only for Status Page Setup Menu and Option Page Setup Menu Reserved Reserved Reserved Reserved Reserved Reserved Load the Optimized Defaults Save all the CMOS changes, only for Main Menu <Esc> 25 GS-R227E-RH Rack Mount Server GETTINGHELP Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen. Status Page Setup Menu / Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window press <Esc>. Select the Load Setup Defaults item in the BIOS Exit Setup menu when somehow the system is not stable as usual. This action makes the system reset to the default settings for stability. Main This setup page includes all the items in standard compatible BIOS. Advanced This setup page includes all the items of Phoenix BIOS special enhanced features. (ex: Auto detect fan and temperature status, automatically configure hard disk parameters. ) Security Change, set, or disable password. It allows you to limit access the system and setup. Server Server additional features enabled/disabled setup menus. Boot This setup page include all the items of first boot function features. Exit There are five optionsin this selection: Exit Saving Changes, Exit Discarding Changes, Load Optimal Defaults, Load Failsafe Defaults, and Discard Changes. 26 BIOS Setup Main Once you enter Phoenix BIOS Setup Utility, the Main Menu (Figure 1) will appear on the screen. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu. Figure 1: Main System Time The time is calculated based on the 24-hour military time clock. [. . . ] Disable this function. IERR & Thermal Trip CPU reduction when IERR occuring and system overheating. After Power Failure This option provides user to set the mode of operation if an AC / power loss occurs. Power On Stay Off Last State System power state when AC cord is re-plugged. Do not power on system when AC power is back. Set system to the last sate when AC power is removed. [. . . ]