User manual GIGABYTE GS-R22PXL

[. . . ] 8 Chapter 1 Features Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Chapter 2 System Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Step 2-1: Chassis Removal and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Step 2-2: CPU Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If any component is missing or damaged in the system, please contact your vendor immediately. To install the peripheral, please go through the following steps. Step 1 Loosen the two riser bracket screws. (See illustrated below) Step 2 Loosen another four riser bracket screws. (See illustrated below) Step 3 Lift the riser bracket slightly, then pull it out from the server chassis. Align the expansion card with the guiding groove. Slide the expansion card into the slot until the card firmly seats. Step 4 Align the riser bracket to the system module. 22 1 1 2 2 3 15 Hardware Installation Process Step 2-6: Hard Disk Drive Installation Step 1 Press the release button. Step 2 Pull the blank out of the drive bay. Step 5 Slide the blank into the bay until it locks into place. Connect cable and power. 1 2 3 4 4 16 Hardware Installation Process Step 2-7: FAN Duct Removal and Installation Step 1 Align the fan duct with the guiding groove. Enter the appropriate option based on this information. (Default setting) CD-ROM: Use for ATAPI CD-ROM drives or double click [Auto] to set all HDD parameters automatically. ATAPI Removable: Removable disk drive is installed here. Multi-Sector Transfer This field displays the information of Multi-Sector Transfer Mode. Disabled: The data transfer from and to the device occurs one sector at a time. Auto: The data transfer from and to the device occurs multiple sectors at a time if the device supports it. LBA Mode This field shows if the device type in the specific IDE channel support LBA Mode. 32-Bit I/O Transfer Mode Ultra DMA Mode Enable this function to max imize the IDE data transfer rate. This field shows the information of Teansfer Mode. This filed displays the DMA mode of the device in the specific IDE channel. 28 BIOS Setup System Information This category includes the information of BIOS version, Product Name, System version, System Serial Number, Main Board Product Name, Main Board Serial Number, LAN1/2 Mac Address, and Reduced Processor. 29 GS-R22PXL Rack Mount Server Advanced About This Section: Advanced With this section, allowing user to configure your system for advanced operation. User can set the Advanced Processor Options, Memory configuration, I/O configuration, and Advanced chipset control. Figure 2: Advanced 30 BIOS Setup Advanced Processor Options Figure 2-1: Advanced Processor Options Advanced Processor Option This category includes the information of CPU Speed, Processor ID and Boot Processor. [. . . ] On Off Enable console redirection after O. S has loaded. (Default setting) 46 BIOS Setup Clear all Event Log Press [Enter] to clear all IPMI event logs. Trigger of CPU Reduction This function provide user to select the CPU reduction situation. This function is supported when dual CPUs operating. Thermal Trip IERR Disabled CPU reduction when system overheat. (Default setting) CPU reduction when IERR occurs. [. . . ]