User manual GIGABYTE GV-R925128T

[. . . ] English Minimum System Requirement · · · · · · IBM® or 100% PC compatible with Pentium® III 650MHz or AMD Athlon 650MHz class processor or higher One available AGP3. 0 compliant slot or better Operating Systems Win® 98/98SE / Win® 2000 / Win® ME / Win® XP 64MB system memory 50MB of available disk space for full installation CD-ROM or DVD-ROM drive Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] How to Reflash BIOS in MS-DOS mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Features · · · · · · Powered by ATi RADEON 9250 Graphics Processing Unit (GPU) Supports the new AGP 8X and latest DirectX 8. 1 Integrated with 128MB DDR memory Supports video capture for video editing (VIVO)(For GV-R925128VH only) Supports TV-Out Supports DVI-I (For GV-R925128D/GV-R925128VH only) and D-Sub connectors Dual display supports with HYDRAVISION English 1. 2. Board Layout 1) GV-R925128D VGA Monitor Connector (15 pins) S-Video DVI-I Connector OR Analog LCD Monitor Analog Monitor VGA Output VGA Monitor Connector (15pin) NTSC / PAL TV AV Output TV-Out (S-Video) Projector DVI Output DVI Connector Digital LCD Monitor DVI-I to D-Sub Connector VGA Output Analog LCD Monitor -2- English 2) GV-R925128VH VGA Monitor Connector (15 pins) VIVO DVI-I Connector OR Analog LCD Monitor Analog Monitor VGA Output VGA Monitor S-Video Input Connector (15pin) VIVO NTSC / PAL TV AV Input AV Output Projector S-Video Output DVI Output DVI Connector Digital LCD Monitor DVI-I to D-Sub Connector VGA Output Analog LCD Monitor -3- 3) GV-R925128T/GV-R92564T English S-Video VGA Monitor Connector (15 pins) AV Output NTSC / PAL TV TV-Out (S-Video) VGA Monitor Connector Projector (15-pin) OR VGA Output Analog Monitor Analog LCD Monitor 2. Hardware Installation Installing your graphics card. Now that you have prepared your computer, you are ready to install your graphics card. If necessary, remove the metal cover from this slot; then align your graphics card with the AGP slot, and press it in firmly until the card is fully seated. Replace the screw to fasten the card in place, and replace the computer cover. -4- English 3. Plug the display cable into your card; then turn on the computer and monitor. 3. DirectX Installation Install Microsoft DirectX to enable 3D hardware acceleration support for Windows® 98/ 98SE / Windows® 2000/ Windows® ME or Windows® XP to achieve better 3D performence. Note: For software MPEG support in Windows® 98/ 98SE/ Windows® 2000/ Windows® ME or Windows® XP, you must install DirectX first. When the Autorun window appears, click Install DirectX. 3. 2. Driver Installation (Windows® XP/2000/ME/98) Insert the driver CD disk into your CD-ROM, and then you can see the AUTORUN window. If it does not show up, please run "D:\setup. exe". (We assume that your CD-ROM drive letter to be D:). Click Install Display Drivers (Radeon 9200 Series). -5- 3. 3. V-Tuner Installation GV-R925128D/GV-R925128T/GV-R92564T: V-Tuner monitors the working frequency of the graphic engine and video memory (Core Clock and Memory Clock). GV-R925128VH: V-Tuner supports monitoring of the temperature, cooling fan speed and voltage of the graphics chip and monitors the working frequency of the graphic engine and video memory (Core Clock and Memory Clock). English Click V-Tuner. GV-R925128D/GV-R925128T/GV-R92564T: GV-R925128VH: 3. 4. HYDRAVISION Installation HYDRAVISION and the Desktop Manager are activated whenever Windows® starts. [. . . ] Begin to flash BIOS by typing atiflash -p 0 filename (ex:r955128d. f1) at the C:\> prompt and press Enter. (atiflash is the name of the flash utility). Restart your PC when it's done. -7- [. . . ]