User manual GIGABYTE LUXO M1004

[. . . ] Malfunction due to interference from other devices 4. Unapproved modification of the product 5. Consequential damage to other devices due to the product's fault. [. . . ] Malfunction arising from natural hazards, e. g. earthquake, lightning, fire, and floods. The product's warranty label has been removed or damaged. The devices inside, including power supply, hard disk, CD-ROM drive, motherboard, ventilator, etc, are not detached from the casing prior to transportation of the computer system, resulting in damage to the casing or other computer-related devices. Any loss/damage caused by failure to follow the installation process with in the user manual. Failure to wear gloves during installation of computer products may cause bodily harm or damage to your devices. Incorrect connector installation may possibly burn out the motherboard and other components. Be sure to observe the instructions in installation manual. English Table of Contents 1. First screw the copper stand offs into the corresponding holes of the chassis. 4-2. 1 4-2. 2 Install the motherboard rear I/O panel (supplied by the motherboard manufacturer). English 4-2. 3 Secure the motherboard with the securing screws (Please refer to your motherboard manual to check what type of motherboard you have). Motherboard ATX Micro ATX Flex ATX Code name A1-A9 U1-U9 F1-F6 Motherboard screws 9 9 6 Case copper post 9 9 6 4-3 Installation of Add-on Card The iSolo 220 does not require any tools for installation of add-on cards, e. g. Required Tools: None 4-3. 1 Unlock the corresponding PCI tool-free fastener by pushing it downwards. 4-3. 2 Lift the fastener upwards and remove the internally attached dust-proof PCI cover. 4-3. 3 Insert the add-on card into the expansion slot and then lock the PCI tool-free fastener. English 4-4 Installation of Front Multi-Media I/O port Incorrect connection of the slots can cause the motherboard to malfunction or completely destroy the motherboard. Please read the manual carefully in the installation as incorrect installations or connection causing faults will void your warranty. The front panel consists of: (1) 2 x USB 2. 0, 1 x IEEE 1394 and 1 x Audio Set (HD & AC'97) (2) Basic casing power switch control cable kit. Required Tools: None Please refer to the instructions supplied by the motherboard manufacturer and make sure the correct type of connector is used prior to installation. (1) x USB . 0, 1 x IEEE 1 and 1 x Audio Set (HD & AC') 4-4. 1 Insert the USB 2. 0 connectors into the corresponding socket on the motherboard. Pin 1 2 3 4 5 Definition Power Power USB DxUSB DyUSB Dx+ Pin 6 7 8 9 10 Definition USB Dy+ GND GND USB Over current USB 2. 0 connector 4-4. 2 Insert the IEEE 1394 connector into the corresponding socket on the motherboard. Pin 1 2 3 4 5 Definition TPA+ TPAGND GND TPB+ Pin 6 7 8 9 10 Definition TPB+12V +12V GND B A C IEEE 1394 connector A IEEE 1394 connector B Pin 1 2 3 4 5 Definition TPA+ TPAGND GND TPB+ Pin 6 7 8 9 10 Definition TPB+12V +12V GND IEEE 1394 connector C Pin 1 2 3 4 5 6 7 8 Definition +12V +12V TPA+ TPAGND GND TPB+ TPB- Pin 9 10 11 12 13 14 15 16 Definition +12V +12V TPA1+ TPA1GND TPB1+ TPB1- 10 English 4-4. 3 Insert the Audio connector into the corresponding socket on the motherboard. HD AUDIO Pin 1 2 3 4 5 Definition MIC2_L GND MIC2_R -ACZ_DET LINE2_R Pin 6 7 8 9 10 Definition FSENSE1 FAUDIO_JD LINE2_L FSENSE2 AC'97 Pin 1 2 3 4 5 Definition MIC GND MIC Power NC Line Out(R) Pin 6 7 8 9 10 Definition NC NC Line Out(L) NC () Basic casing power switch control cable kit. Connector Speaker Power SW Power LED HDD LED Follow the connectors list below for installation (see figure below) Color Yellow(+) / Black(-) Orange(+) / White(-) Green(+) / White(-) Red(+) / White(-) Different motherboards have different installation areas and specifications, screw holes and connectors. For detailed instructions, please refer to the motherboard user manual supplied by the motherboard manufacturer. 4-5 Connection of Fan Power Cables The iSolo 220 has one 12cm silent cooling fan in the front and one in the rear. This case includes internal connectors that connects the front and rear fans making it a single 3-pin connector. [. . . ] For detailed instructions, please refer to the motherboard user manual supplied by the motherboard manufacturer. 4-5 Connection of Fan Power Cables The iSolo 220 has one 12cm silent cooling fan in the front and one in the rear. This case includes internal connectors that connects the front and rear fans making it a single 3-pin connector. Required Tools: None Plug the 3-pin connector into the corresponding system fan socket on the motherboard. 4-5. 1 11 English 4-6 Installation of 5. 25" Front Device Bay 4-6. 1 Detach the front panel (see step 1-3. 2 on page 5) and remove the mesh drive rail from the front panel. 4-6. 2 Remove the front EMI plate and attach the front panel onto the chassis. 4-6. 3 Slide the 5. 25" device into the drive bay from the front of the chassis. 4-6. 4 Secure the 5. 25" device with the internal latch. [. . . ]