User manual GIGABYTE MNNM1PI

[. . . ] MNNM1PI Intel® mini-ITX Motherboard USER’S MANUAL Intel® mini-ITX Motherboard Rev. 1001 * The WEEE marking on the product indicates this product must not be disposed of with user's other household waste and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!The WEEE marking applies only in European Union's member states. * Copyright © 2010 GIGA-BYTE TECHNOLOGY CO. , LTD. The trademarks mentioned in the manual are legally registered to their respective companies. Notice The written content provided with this product is the property of Gigabyte. [. . . ] The advanced menu includes sub-menu of CPU Configuration, IDE Configuration, Floppy Configuration, Super IO Configuration, Hardware Health Configuration, ACPI Configuration, MPS Configuration, and USB Configuration. Main Advanced PCIPnP Boot BIOS SETUP UTILITY Security Chipset Exit Advanced Settings WARNING: Setting wrong values in below sections may cause system to malfucntion. CPU Configuration IDE Configuration Super IO Configuration Hardware Health Configuration ACPI Configuration USB Configuration   +Tab F1 F10 ESC v02. 61 (C) Copyright 1985-2006, American Megatrends, Inc. Select Screen Select Item Change Field Select Field General Help Save and Exit Exit 25 MNNM1PI Motherboard CPU Configuration Main Advanced PCIPnP Boot BIOS SETUP UTILITY Security Chipset Exit CPU Configuration Module Version: 3F. 15 Manufacturer: Intel Intel (R) Atom(TM) CPU K410 Frequency :1. 66GHz FSB :666MHz Cache L1 :24KB Cache L2 :512KB Ratio Actual Vaule : 10 Max CPUID Value Limit Execute-Disable Bit Capability @ 1. 66GHz [Disabled] [Enabled]   +Tab F1 F10 ESC Select Screen Select Item Change Field Select Field General Help Save and Exit Exit v02. 61 (C) Copyright 1985-2006, American Megatrends, Inc. CPU Information This category includes all the information of CPU manufacturer, type, Frequency, FSB, L1/ L2 Cache, Ratio Status, and Ratio actual value Please note that setup menu options will be variable depends on the type of CPU. Max CPUID Value Limit When the computer is booted up, the operating system executes the CPUID instruction to identify the processor and its capabilities. Before it can do so, it must first query the processor to find out the highest input value CPUID recognizes. This determines the kind of basic information CPUID can provide the operating system. The maximum CPUID input value determines the values that the operating system can write to the CPUID's EAX register to obtain information about the processor. Enabled Disabled Enabled Disabled Enable Max CPUID Value Limit. (Default setting) Enable Execute Disable Bit Capability. (Default setting) Disable Execute-Disable Bit function. Execute-Disable Bit Capability 26 MNNM1PI Motherboard IDE Configuration Main Advanced PCIPnP Boot BIOS SETUP UTILITY Security Chipset Exit IDE Configuration Configure SATA as Primary IDE Master Secondary IDE Master IDE Detect Time Out (Sec) [35] [IDE]   +Tab F1 F10 ESC v02. 61 (C) Copyright 1985-2006, American Megatrends, Inc. Select Screen Select Item Change Field Select Field General Help Save and Exit Exit Confiure SATA as ACHI When set to AHCI, the SATA controller enables its AHCI functionality. However, its RAID functions will be disabled and you won't be able to access the RAID setup utility at boot time. When set to IDE, the SATA controller disables its RAID and AHCI functions and runs in the IDE emulation mode. You won't have access to the RAID setup utility. (Default setting) Disable the device. IDE Disabled Primary IDE Master, Slave The category identifies Serial ATA and IDE types of hard disk that are installed in the computer. System will automatically detect HDD type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. Hard drive information should be labeled on the outside device casing. Enter the appropriate option based on this information. TYPE Not Installed: No device is installed. 27 MNNM1PI Motherboard Auto: Set parameters automatically. (Default setting) CD-ROM: Use for ATAPI CD-ROM drives or double click [Auto] to set all HDD parameters automatically. LBA/Large Mode Configure the device type in the specific IDE channel support LBA Mode. (Default setting) Block (Multi-Sector Transfer) Configure the information of Multi-Sector Transfer Mode. Disabled: The data transfer from and to the device occurs one sector at a time. [. . . ] (Default setting) Prevents User access to the setup utility. Allows only limited fields to be changed such as Date and Time. Allows access to the setup utility but the fields can not be changed. NOTE!!This item will pops up when Suervisor Password is set. Password Check Setup Always Check the password while invoking setup. [. . . ]