User manual GIGABYTE SUMO 4112

[. . . ] The devices inside, including power supply, hard disk, CD-ROM drive, motherboard, ventilator, etc, are not detached from the casing prior to transportation of the computer system, resulting in damage to the casing or other computer-related devices. Any loss/damage caused by failure to follow the installation process with in the user manual. Failure to wear gloves during installation of computer products may cause bodily harm or damage to your devices. Incorrect connector installation may possibly burn out the motherboard and other components. [. . . ] Place the power supply unit into the case. Secure the power supply with the 4 securing screws. When using large power supply unit, please disassemble the cross bar by loosening screws. Fasten the screws to secure the cross bar after the power supply installed. 4-1. 2 4-1. 3 4-1. 4 4-1. 1 4-2 Installation of Motherboard Required parts: Copper stand offs, Motherboard screws This chassis supports CEB / ATX / Micro ATX motherboards. Please confirm the dimensions and fixing points of the motherboard prior to installation. 4-2. 1 According to the motherboard's specifications, select the proper screw points. Screw in the copper stand offs into the corresponding points on the motherboard. 4-2. 2 Change the motherboard I/O bracket on the rear panel (supplied by the motherboard manufacturer). 4-2. 3 Secure the motherboard with the motherboard Motherboard Code on tray Securing screw Copper stand off screws (refer to your motherboard manual to CEB E1-E8 8 8 ATX A1-A9 9 9 check what type of motherboard you have). Micro ATX M1-M9 9 9 4-2. 1 4-2. 2 4-2. 3 4-3 Installation of Add-On card This chassis supports tool-free installation of add-on cards, e. g. graphics cards, sound cards, and etc. Required Tools: None 4-3. 1 4-3. 2 4-3. 3 4-3. 4 Unlock the PCI slot clamp. Remove the internally attached PCI slot blanking plate. Insert the add-on card into the expansion slot with care. 4-3. 2 4-3. 3 4-3. 4 4-3. 1 08 English 4-4 Installation of Front Multi-Media I/O Ports Incorrect connection of sockets can cause the motherboard to malfunction or completely destroy the motherboard. Please observe the installation instructions in the manual carefully as incorrect installations or connection causing faults will void your warranty. The top panel includes: (1) 1 x eSATA, 2 x USB 2. 0, 1 x IEEE 1394 and 1 x Audio Set (HD or AC'97) (2) Basic casing power switch control cable kit Required Tools: None Please refer to the instructions supplied by the motherboard manufacturer and make sure the correct type of connector is used prior to installation. (1) 1 x eSATA, 2 x USB 2. 0, 1 x IEEE 1394 and 1 x Audio Set (HD or AC'97) 4-4. 1 Insert the eSATA connector into the corresponding socket on the motherboard. 4-4. 2 Insert the USB 2. 0 connectors into the corresponding sockets on the motherboard (please refer to the motherboard user manual for further information). USB 2. 0 connector Pin Definition Pin 1 2 3 4 5 Power Power USB DxUSB DyUSB Dx+ 6 7 8 9 10 USB Over current Definition USB Dy+ GND GND 4-4. 3 Insert the IEEE 1394 connector into the corresponding socket on the motherboard. IEEE 1394 connector A Pin 1 2 3 4 5 Definition TPA+ TPAGND GND TPB+ Definition TPA+ TPAGND GND TPB+ Pin 6 7 8 9 10 Pin 6 7 8 9 10 GND +12V +12V GND Definition TPB+12V +12V Definition TPB- B A IEEE 1394 connector C C Pin 1 2 3 4 5 6 7 8 Definition +12V +12V TPA+ TPAGND GND TPB+ TPBPin 9 10 11 12 13 14 15 16 TPB1+ TPB1Definition +12V +12V TPA1+ TPA1GND IEEE 1394 connector B Pin 1 2 3 4 5 4-4. 4 Insert the Audio connector into the corresponding socket on the motherboard. HD AUDIO Pin 1 2 3 4 5 Definition MIC2_L GND MIC2_R -ACZ_DET LINE2_R Definition MIC GND MIC Power NC Line Out(R) Pin 6 7 8 9 10 Pin 6 7 8 9 10 Line Out(L) NC LINE2_L FSENSE2 Definition NC NC Definition FSENSE1 FAUDIO_JD AC'97 Pin 1 2 3 4 5 English 09 (2) Basic casing power switch control cable kit Follow the connectors list below for installation (see figure below) Connector Power LED Power SW Color Green(+) / Wite(-) Orange(+) / White(-) 4-5 Connection of Fan Power Cable This chassis has 1 x 12cm silent cooling fan at the front and 1 x 12cm silent fan at the rear. [. . . ] 4-9. 4 Press the eject button and remove the 2. 5"HDD mobile enclosure from the 5. 25" front device housing. 4-9. 1 4-9. 2 4-9. 3 4-9. 4 4-10 Application of DIY inter changeable LED lighting 4-10-1 Remove front panel following instruction in 1-3. 4-10-2 Detach the LED holder by simply squeeze the securing hook at top and bottom softly. [. . . ]