User manual GIGABYTE TA1

[. . . ] TA Series User's Manual Introduction Thank you for purchasing TA series. Please read the following instructions carefully to ensure you can use this product safely. Please follow the warning signs and instructions of the product. [. . . ] PC case Overall dimension With side cover: 70(W)mm x 236(H)mm x 213(D)mm Without side cover: 64(W)mmx230(H)mmx213(D)mm Materials of the case has been tested to comply with the UL specification and designed for space and screw saving purposes. Users simply need to remove one screw from the back to unload the case cover and access to the inside of the case. Moreover, the case has been designed with anti EMI function and complies with standard PC safety standards. P. System equipment installation Unload case Step 1: Remove the screw from the bottom of the case. Step 2: Grasp the handle on the panel and pull out the case. P. 5 TA Series User's Manual Installing hard drive Step 1: Fix the hard drive on the base with 4 screws and connect the hard drive with the IDE ribbon cable. Install hard drive on top of the screw stands on the base. ) Screw stands (Attention!Make sure that the red (fool-proof) wire on the ribbon cable should be connected to PIN 1 of the hard drive as shown below. ) Red (fool-proof) wire should be connected to PIN 1. P. 6 TA Series User's Manual Step 2: Fix the hard drive with its rack on the four posts and connect the ribbon cable to the IDE connector (J1). P. 7 TA Series User's Manual Installing DOM (DISK On Module) Step 1: Install DOM on the DOM slot (J1). Attention!Make sure that DOM and HDD cannot be used at the same time. Installing DOC (Disk On Chip) Step 1: Install DOC on the DOC slot (U12) Pin1 Attention!8 TA Series User's Manual Installing CD-ROM Step 1: Fix the slim CD-ROM on the base with 4 screws (2 on each side). Step 2: Slide slim CD-ROM and the base to the rack (J4). Step 3: Fix the CD-ROM and the base on the rack with 2 screws. P. 9 TA Series User's Manual Installing PCMCIA Step 1: Fix PCMCIA card next to the Slim CD-ROM with 2 screws. Step 2: Unload the hard drive from another side of the PC. Then fix the PCMCIA card on the bolts between the 4 posts on which the hard drive is fixed. P. [. . . ] Dispose batteries as instructed by their manufacturers. P. 13 TA Series User's Manual For use on TA1 series GA-TC2000MB Main Board Specification Processor VIA C3 EBGA 733MHz and Above Auto 100/133 MHz FSB Auto Detect CPU Voltage Chipset VIA VT8601T (PLE 133T) VIA VT82C686B Chipset with Built-in enhanced Graphics AC97 Audio Codec-Realtek ALC202A LAN Controller-Realtek RTL8100BL DRAM 2x168 Pin DIMM Sockets Supports PC100/PC133 SDRAM Supports Up to 1. 0GB SDRAM Supports only 3. 3V SDRAM I/O 1 x UDMA ATA 33/66/100 Bus Master IDE Ports (For 44 Pin 2. 5 Inch Notebook HDD or DOM-Disk On Module) 2x COM Port 1x LPT Port 2x PS/2 Keyboard and Mouse Port 1x VGA(DB15) Port 1x Line-in , 1x Line-out , 1x Mic Jack 4x USB Ports (2xRear and 2x Front) 1x LAN Port 1x DOC(Disk on Chip-Must be used 3. 3V) Socket Form Factor Mini-ITX (17*17cm) H/W Monitoring System FAN revolution detect System Temperature detect System voltage detect(Vcore, VDD, VCC, +12V) P. 14 TA Series User's Manual BIOS 2Mbit Flash RAM AC recovery ON/OFF control Auto detect &report system health status Other Features Suspend to RAM(STR) Support Wake-On-LAN(WOL) Front Line-out and Mic Connector Front Panel Connector (Power switch , Power LED , HDD LED , LAN Activity LED and Reset switch) Poly fuse for Keyboard Over-Current Protection P. [. . . ]