User manual GIGABYTE TA2

[. . . ] TA manual ENG. p65 1 TA Series User's Manual Introduction Thank you for purchasing TA series. Please read the following instructions carefully to ensure you can use this product safely. [. . . ] Use only the same or equivalent batteries for eplacement. Dispose batteries as instructed by their manufacturers. English TA manual ENG. p65 3 TA Series User's Manual 2 TA Series User's Manual 1. PC case Overall dimension With side cover: 70(W)mm x 236(H)mm x 213(D)mm Without side cover: 64(W)mmx230(H)mmx213(D)mm Materials of the case has been tested to comply with the UL specification and designed for space and screw saving purposes. Users simply need to remove one screw from the back to unload the case cover and access to the inside of the case. Moreover, the case has been designed with anti EMI function and complies with standard PC safety standards. 4 5 6 7 8 Specifications -Product specification -PC case -TA series Motherboard -Power supply unit -24X Slim CD-ROM or DVD-Rom (Optional) -PCMICA Slot (optional) -2. 5-inch Slim HDD (Optional) -Power cord -Keyboard and mouse (Optional and subject to real products at shipment) -Accessories System Assembly Manual Driver CD Ribbon cable Screws for Slim HDD and Slim CD-ROM System Packing Man u a l an d Driver CD *Keyboard (Optional) *mouse (Optional) 9 10 Front Panel 1. MIC 2. Audio Out 3. USB Ports 4. Power Button 5. Power LED 6. LAN LED 7. HDD LED 8. CD Button 2. Parts on Panels 3 1 2 3 9 9. PCMCIA Slot 10. PCMCIA Button 2 10 ( TA1 ) 1 2 3 11 4 5 6 7 12 16 15 5 6 7 9 10 1 2 3 ( TA2) 9 10 1 2 15 11 16 3 13 4 5 6 7 ( TA4) Power cord 11 PC 4 8 8 8 14 Rear Panel 1. Keyboard (PS2) 2. USB port 3. VGA/DVI 4. COM 1 5. Audio Out 6. Audio In 7. MIC 8. Power Cord 9. Mouse (PS2) 10. LAN (RJ45) 11. LPT 12. COM 2 13. SPDIFOut 14. System FAN 15. IEEE 1394 16. S Video Specification with "Option" are subject to change without notice. English English TA manual ENG. p65 5 TA Series User's Manual 4 TA Series User's Manual Step 2: Fix the hard drive with its rack on the four posts and connect the ribbon cable to the IDE connector (J1). 3. System equipment installation Unload case Step 1: Remove the screw from the bottom of the case. Installing DOM (DISK On Module) Step 1: Install DOM on the DOM slot (J1). Step 2: Grasp the handle on the panel and pull out the case. 5 4 Installing hard drive Step 1: Fix the hard drive on the base with screws and connect the hard drive with the IDE ribbon cable. Attention!Make sure that DOM and HDD cannot be used at the same time. Installing DOC (Disk On Chip) Step 1: Install DOC on the DOC slot (U12) Pin 1 Screw stands (Attention!Install hard drive on top of the screw stands on the base. ) Attention!Use 3. 3V DOC. Red (fool-proof) wire should be connected to PIN 1. Make sure that the red (fool-proof) wire on the ribbon cable should be connected to PIN 1 of the hard drive as shown below. ) English English TA manual ENG. p65 7 TA Series User's Manual 6 TA Series User's Manual Installing PCMCIA Step 1: Fix PCMCIA card next to chassis with screws. Installing CD-ROM Step 1: Fix the slim CD-ROM on the base with 4 screws (2 on each side). Step 2: Slide slim CD-ROM and the base to the rack (J4). Step 2: Unload the part from another side of the PC. Then fix the PCMCIA card on the bolts and Fix the PCMCIA Card with screws. 7 6 Step 3: Fix the CD-ROM and the base on the rack with 2 screws. ( C3 Type) ( P4 Type) Step 3: Re-Fix the parts with screws. English English TA manual ENG. p65 8 TA Series User's Manual Installing memory Align the fool-proof clicks on the bottom of the RAM module to the socket, and the locks on the socket should securely lock on the clicks at sides of the module as shown in the above picture. [. . . ] Use only the same or equivalent batteries for replacement. Dispose batteries as instructed by their manufacturers. English [. . . ]