User manual GIGABYTE TRITON 180

[. . . ] Triton Series Triton + Triton 180 Triton GZ-XX1CA-SNS/SNB Triton 180 GZ-AX1CA-SDS/SDB GZ-AX1CA-SD1/SD2 English User's Manual English Triton 180 Triton Thank you for purchasing GIGABY TE thermal product. [. . . ] Any loss/damage caused by failure to follow the installation process with in the user manual. Failure to wear gloves during installation of computer products may cause bodily harm or damage to your devices. Incorrect connector installation may possibly burn out the motherboard and other components. Be sure to observe the instructions in the user manual. English Table of Contents 1. Components Introduction 1-1 Casing's Internal Structure 1-2 Front and Rear Panel Structure 1-3 Removal of Side and Front Panels 4 4 5 6 2. Installation Instructions 8 4-1 Installation of Power Supply 8 4-2 Installation of Motherboard 8 4-3 Installation of Add-on Card 9 11 12 13 13 13 14 4-4 Installation of Front Multi-Media I/O Port 10 4-5 Installation of Fan Power Cable 4-7 Installation of 3. 5" Front Device Bay 4-8 Installation of 3. 5" Internal Device Bay 4-9 Foot Supports 4-10 Liquid Cooling System Support 4-11 Recommended Cooling Products 4-6 Installation of 5. 25" Front Device Bay 12 English 1. Components Introduction 1-1 Casing's Internal Structure 1 8 5 6 7 1 Power Supply Motherboard Tray PCI Tool-Free Fastener 5 6 5. 25" Front Device Bay 3. 5" Front Device Bay 3. 5" Internal Device Bay English 7 Securing Runner x6 Copper Stand Off x9 Motherboard Securing Screw x 9 Accessory Box Power Supply Securing Screw x 4 Wire Clamp x 1 Magnet Ring x 1 8 USB 2. 0 Audio Set (HD & AC'97) IEEE1394 (Multi-connectors) Front Cable Kit 3-Pin Fan Connector Basic chassis power switch control cable kit 1-2 Front and Rear Panel Structure a) Front Panel b) Rear Panel a-1 b-1 a- b- Triton 180 Triton a-1) Reset SW / HDD LED / Power SW / Power LED a-2)Front multi-media I/O ports (USB x2, IEEE 1394 x1, Audio Set x1 (HD &AC'97)) b-1) Rear Fan b-2) LCS Tube Inlet/Outlet 5 English 1-3 Removal of Side and Front Panels 1-3. 1 To remove side panels: 1-3. 1a Remove the 4 thumb screws at the rear of the side panels, and detach the side panels. 1-3. 2 To remove front panel: 1-3. 2a Remove the left and right side panels (see step 1-3. 1), release the 4 clamps the hold the front panel onto the chassis. 2. Features -High Quality Design · High-end aluminum bezel design · Skid-proof & shock-proof foot stands -Complete Support · Front panel multi-media I/O ports (USB x2, IEEE 1394 x1, Audio Set x1 (HD &AC'97)) · Dual 12cm silent & shock proof fan (Front x 1 and Rear x 1) · Supports liquid cooling systems -Integration of Cooling Technology · Intel CAG 1. 1 Air Duct -Convenience of Assembly · Internal Cable Management · Tool-free installation design 6 English 3. Specifications Triton Model Case Type Size (W x H x D) Front Bezel Material Color Side Panel Body Material Net Weight 5. 25" Device Bay (external) 3. 5" Device Bay (external) 3. 5" Device Bay (internal) PCI Slot Motherboard Size System Fan (front) System Fan (rear) Multi-Media I/O Port GZ-XX1CA-SNS/SNB Triton 180 GZ-AX1CA-SDS/SDB GZ-AX1CA-SD1/SD2 Middle Tower 200 x 440x 480 mm Aluminum Silver / Black Intel CAG1. 1 0. 7 mm SECC 8. 4kg 5 2 3 7 ATX / Micro ATX / Flex ATX 12cm silent fan x 1 12cm silent fan x 1 USB2. 0 x 2 , IEEE 1394 x 1 , Audio Set x 1 (HD & AC'97) 7 English 4. Installation Instructions Please follow the reference sections in order for installation. 4-1 Installation of Power Supply To facilitate the installation, it is recommended to set the chassis upright on the table. Required Tools: Power supply securing screw x 4. 4-1. 1 Remove side panel (see step 1-3. 1 on page 6). Place the power supply unit into the case. 4-1. 2 Secure the power supply with the 4 securing screws. 4-2 Installation of Motherboard This chassis is compatible with ATX / Micro ATX / Flex ATX motherboards. Please confirm the dimensions and fixing points of the motherboard prior to installation. Required Tools: Copper stand offs, Motherboard screws. 4-2. 1 According to motherboard specifications, select proper screw points, screw in the copper stand offs into the corresponding points on the motherboard. 4-2. 2 Change the motherboard I/O bracket on the rear panel (supplied by the motherboard manufacturer). 8 English 4-2. 3 Secure the motherboard with the motherboard screws (refer to your motherboard manual to check what type of motherboard you have). Motherboard ATX Micro ATX Flex ATX Code name A1-A9 U1-U9 F1-F6 Motherboard screws 9 9 6 Case copper post 9 9 6 4-3 Installation of Add-on Card Required Tools: None This chassis supports tool-free installation of add-on cards, e. g. Unlock the corresponding PCI tool-free fastener by pushing it downwards. 4-3. 1 4-3. 2 Lift the fastener upwards and remove the internally attached dust-proof PCI cover. 4-3. 3 Insert the add-on card into the expansion slot and then lock the PCI tool-free fastener. English 4-4 Installation of Front Multi-Media I/O Ports Incorrect connection of the slots can possibly cause the motherboard to malfunction or completely destroy the motherboard. [. . . ] While installing the liquid cooling system, please refer to the manual provided with the liquid cooling system. 1 English 4-11 Recommended Cooling Products This chassis is recommended to be used with GIGABYTE cooling products. 1 [. . . ]