User manual GN NETCOM GN STRATUS ULTRA

[. . . ] With your thumb, close the ear lobe hinge until it is snug, secure and comfortable to wear, but not tight on your ear. Lightly press the speaker against the ear for proper positioning. To remove, simply lift the Stratus Ultra-G off your ear. Figure 2 Stratus Ultra-G Ear Capsule Figure 3 Ear Capsule Wearing 2 Changing Ears 1. Hold the receiver assembly in your left hand with the microphone boom perpendicular to the floor. [. . . ] Refer to the Microphone Positioning section for additional information. Figure 10 Headband Wearing 5 Microphone Positioning To take advantage of the noise canceling qualities of the microphone, position the Stratus Ultra-G headset with the flat side of the microphone, marked with an F facing you. The microphone boom should be adjusted so that the , microphone is approximately one finger width away from your lower lip (see Figure 11). The Stratus Ultra-G has a flexible boom that can be reshaped until the microphone is correctly positioned in front of your mouth. One hand should grasp and steady the receiver end of the boom. The other hand can then flex the boom (see Figure 12). CAUTION: Never forcefully rotate the microphone boom past its stop point in the receiver assembly! 1 Finger Width Figure 11 Microphone Positioning Figure 12 Clothing Clip The clothing clip should be fastened for comfortable wearing (see Figure 13). It is designed to prevent the weight of the cord from dislodging the headset. Position the clip conveniently on your clothing. To reduce excess slack, reposition the clip by sliding it up and down the cord. Figure 13 Clothing Clip 6 Connecting to Your Telephone An amplifier is often needed to connect the headset to the telephone or telephone system. For these applications, the headset is equipped with a Quick Disconnect plug which mates to a Quick Disconnect jack on the amplifier. Follow the instructions supplied with the amplifier to connect the headset and amplifier to your telephone or telephone system (see Figure 14). Some telephones do not require amplification. For these applications the headset is equipped with a cable with a modular plug on the end. The modular connector plugs directly into a headset port (modular jack) on the telephone or console. The modular plug cable also has a mated Quick Disconnect assembly (see Figure 15). Disconnecting at the Quick Disconnect allows you to move around without having to remove your headset. If you are on a call, disconnecting at the Quick Disconnect effectively puts the other party on hold until you return. Netc om e mut t dse hea off on off on me volu high Figure 14 Amplified Configuration low Maintenance The foam covers on the receiver and microphone can be washed in mild soap and water. Replacement covers are available from your GN Netcom distributor. Figure 15 Unamplified Configuration 7 Cautionary Notes to Computer Users When using any headset with a computer, care should be taken in dry or low humidity environments to protect the user from electrostatic discharge from the monitor (CRT). Computer monitors can induce a substantial electrostatic charge when turned on or off, or when there is a power failure, and the resulting electrostatic discharge can be passed through the headset to ground. A user in close proximity to or touching the computer may feel a common "shock" sensation, similar to touching a doorknob after walking across a carpet, causing no harm to the user. This discharge is entirely due to the computer monitor; the headset is merely the shortest path to ground. To minimize the possibility of electrostatic discharge through the headset, you can: · Use a grounded screen in front of the monitor. · Use static dissipative wrist straps. [. . . ] · This warranty gives you specific legal rights and you may have other rights which vary from state to state. Unless otherwise instructed in the User Guide, the user may not, under any circumstances, attempt any service, adjustments or repairs on this unit, whether in or out of warranty. It must be returned to the factory or authorized service agency for all such work. To Obtain Service For customer service and technical support, call GN Netcom, Inc. If it becomes necessary to send a unit in for repair, it is not necessary to call for a Return Material Authorization (RMA) number, as one will be assigned upon receipt of the package at the factory. [. . . ]