User manual GRACO 15H873 9-2010

[. . . ] 1 shows the cover (32) on the stand side; the motor side cover is (21). Place a clean rag over the top of the slider cylinder (2) to prevent debris from falling into the slider assembly during disassembly. 9 Place clean rag over slider cylinder (2). Hold slider piston (9) flats with 3/4 in. wrench, and brace against tie rod (3). Kit Parts NOTE: Drive Linkage Rebuild Kit 15H873 includes parts to rebuild one drive linkage assembly. [. . . ] Torque key-side screw to 210-230 ft-lb (283-310 N·m) first, then torque gap side screw to 210-230 ft-lb (283-310 N·m). ti9225a 12 5 FIG. Rotate Crank Arm 38 39 9 ti9224b FIG. Remove Crank Arm Cap 311598C 3 Kit Installation Reassembly 1. Orient the new connecting rod (7*) and slider piston (9*) as shown. Assemble the crank arm (4), retaining rings (6*), pin (10*), and retaining ring (11*). Position the crank arm (4) to engage the output shaft (OS), and rotate it to the bottom of the output shaft. Place a clean rag over the top of the slider cylinder (2) to prevent debris from falling into the slider assembly during reassembly. Apply antiseize lubricant to the threads of the cap screws (5*). Install the key (39), crank arm cap (38), and cap screws (5*), oriented as shown. While the gap-side screw is still loose, torque the key-side screw to 210-230 ft-lb (283-310 N·m). Then torque the gap-side screw to 210-230 ft-lb (283-310 N·m). 7* GZ *9 *8 8* 10* 11* ti8717a 9 12 Place clean rag over slider cylinder (2). Apply antiseize lubricant to screw (5) threads. Torque key-side screw to 210-230 ft-lb (283-310 N·m) first, then torque gap side screw to 210-230 ft-lb (283-310 N·m). 5* 38 12 FIG. Lubricate the lower bearing on the connecting rod with 1 shot (1 cc) of 107411 Grease or equivalent, using grease zerk (GZ). The top bearing is prelubricated and does not require grease at installation. Install the two new bearings (8*) on the slider piston (9*). The joints between the bearings must align with the pin hole (PH) in the slider piston. ti9224b 39 9 FIG. Slide the piston (9*) and connecting rod (7*) into the cylinder (2). ti8719a 8. Ensure that the collars (13) are in place in the coupling nut (14). wrench on the flats of the slider piston (9*), to keep it from turning when you are tightening the coupling nut (14). Orient the wrench so it is braced against one of the tie rods (3) or the pump stand. Tighten the coupling nut (14) onto the slider piston (9*) and torque to 75-80 ft-lb (102-108 N·m). [. . . ] In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise. FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées. Graco Information For the latest information about Graco products, visit www. graco. com. TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor. [. . . ]