User manual GRACO 15H882 9-2010

[. . . ] 1 shows the cover (32) on the stand side; the motor side cover is (21). 9 10 Place clean rag over slider cylinder (2). Hold slider piston (9) flats with 3/4 in. wrench, and brace against tie rod (3). 32 Kit Parts NOTE: Slider Bearing Kit 15H882 includes parts to rebuild both slider bearing assemblies. Parts included in the kit are marked with an asterisk, for example (5*). [. . . ] Rotate the crank arm (4) to allow it to be removed from the output shaft (OS). Pull the crank arm/connecting rod/slider piston assembly (CR) up and out of the cylinder. Remove the old bearings (8). 311616C 3 Kit Installation Reassembly 1. Install the two new bearings (8) on the slider piston (9). The joints between the bearings must align with the pin hole (PH) in the slider piston. 9 12 Place clean rag over slider cylinder (2). Apply antiseize lubricant to screw (5) threads. Torque key-side screw to 210-230 ft-lb (283-310 N·m) first, then torque gap side screw to 210-230 ft-lb (283-310 N·m). 5 12 38 7 9 8 PH FIG. Slider Bearings ti9224b ti8719a 8 39 9 2. Slide the piston (9) and connecting rod (7) into the cylinder (2). Position the crank arm (4) to engage the output shaft (OS), and rotate it to the bottom of the output shaft. Place a clean rag over the top of the slider cylinder (2) to prevent debris from falling into the slider assembly during reassembly. Apply antiseize lubricant to the threads of the cap screws (5). Install the key (39), crank arm cap (38), and cap screws (5), oriented as shown. While the gap-side screw is still loose, torque the key-side screw to 210-230 ft-lb (283-310 N·m). Then torque the gap-side screw to 210-230 ft-lb (283-310 N·m). Ensure that the collars (13) are in place in the coupling nut (14). wrench on the flats of the slider piston (9), to keep it from turning when you are tightening the coupling nut (14). Orient the wrench so it is braced against one of the tie rods (3) or the pump stand. Tighten the coupling nut (14) onto the slider piston (9) and torque to 75-80 ft-lb (102-108 N·m). Reinstall the cover (32 or 21) and screws (12). Install Crank Arm Cap 4 311616C Kit Installation 311616C 5 Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. [. . . ] In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise. FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées. Graco Information For the latest information about Graco products, visit www. graco. com. TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor. [. . . ]