User manual GRACO 15V534 GUN FLUSH INSTRUCTIONS PARTS

[. . . ] Each 15V826 Kit includes one gun flush box and related parts. The pressure switch, air flow switch, and solenoid valve included in Gun Flush Box Kit 15V826 will be installed in this interface module. ProMixTM 2KS PART NO. SERIES SERIAL GFB CONTROL MODULE MAX AIR WPR . 7 C Intrinsically safe equipment for Class I, Div 1, Group D, T3 US Ta = -20°C to 50°C Install per 289833 7 bar 100 PSI GRACO INC. Box 1441 Minneapolis, MN 55440 U. S. A. MPa FM08ATEX0073 II 2 G Ex ia IIA T3 Artwork No. [. . . ] Connect the wires from PS#1 to the right side of the terminal strip (12) pins 5 (+) & 6 (-), as indicated by the label (21). 12 21 Pressure switch is part of gun flush box kit; not included with GFB Interface Kit. 1 PS#1 TI14279a FIG. Connect Pressure Switch to Terminal Strip 3. If using a second gun flush box, connect the wires from PS#2 to the right side of the terminal strip (12) pins 7 (+) & 8 (-), as indicated by the label (21). 6 and Table 1. PS#2 1 TI14282a FIG. Install Pressure Switch (two shown) 6 313212A Installation Install the Solenoid NOTE: The GFB Interface Module Kit does not include a solenoid (SO). The solenoid is supplied with the gun flush box kit. Install the solenoid in the interface module as follows. Each gun flush box kit includes one solenoid (SO). The GFB interface module can accommodate 1 or 2 solenoids. Install the solenoid(s) on the manifold at the bottom rear of the enclosure. If you are using two gun flush boxes, remove the two sealing screws (4) from the solenoid manifold (8) before installing SO#2. Also remove the plug (5) from the connector (15). 1 2. Connect the wires from SO#1 to the right side of the terminal strip (12), as indicated by the label (21); red (+12V) to pin 9, black (COM) to pin 10. 12 21 Solenoid is part of gun flush box kit; not included with GFB Interface Kit. TI14279a FIG. If using a second gun flush box, connect the wires from SO#2 to the right side of the terminal strip (12), as indicated by the label (21); red (+12V) to pin 11, black (COM) to pin 12. 8 and Table 1. 1 SO#1 1 SO#2 TI14282a FIG. Install Solenoid (two shown) 313212A 7 Installation Connect the Cable to the RoboMix Control Board NOTICE To avoid damaging circuit board when servicing, wear grounding strap on wrist and ground appropriately. Open the RoboMix to access the control board. Connect the 10 position connector (24) to J1 on the control board. 9. J1 Pins 1-4, 7-10 (10 position Connector 24) FIG. 9: RoboMix Control Board J1 Connections 3. [. . . ] Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties. In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise. FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées. Graco Information For the latest information about Graco products, visit www. graco. com. [. . . ]