User manual GRACO 255216 9-2010

[. . . ] 1 shows the cover (32) on the stand side; the motor side cover is (21). Place a clean rag over the top of the slider cylinder (2) to prevent debris from falling into the slider assembly during disassembly. 9 Place clean rag over slider cylinder (2). Hold slider piston (9) flats with 3/4 in. wrench, and brace against tie rod (3). Kit Parts NOTE: Wrist Pin Replacement Kit 15H873 includes parts to replace the wrist pin bearings on both drive linkage assemblies. [. . . ] Drive Linkage Assembly 311609C 3 Kit Installation Reassembly 1. Install the new wrist pin bearing (7a*) on the connecting rod (7). Align the hole in the bearing with the grease passage in the connecting rod (7). Orient the new connecting rod (7) and slider piston (9) as shown. Assemble the pin (10*) and retaining ring (11). Slider Bearings X GZ 7 GZ 9 8 7a 8 10* 11 ti8717a ti8719a 7 9 8 6 4 5. Slide the piston (9) and connecting rod (7) into the cylinder (2). Position the crank arm (4) to engage the output shaft (OS), and rotate it to the bottom of the output shaft. Place a clean rag over the top of the slider cylinder (2) to prevent debris from falling into the slider assembly during reassembly. Apply antiseize lubricant to the threads of the cap screws (5*). Install the key (39), crank arm cap (38), and cap screws (5*), oriented as shown. While the gap-side screw is still loose, torque the key-side screw to 210-230 ft-lb (283-310 N·m). Then torque the gap-side screw to 210-230 ft-lb (283-310 N·m). FIG. Lubricate the crank pin bearing (X) and the wrist pin bearing (7a) with 1 shot (1 cc) of 107411 Grease or equivalent, using grease zerks (GZ). NOTE: Lubricate the wrist pin bearings (7a) every 6 months and the crank pin bearings (X) annually. Replace the wrist pin bearings annually. Install the two bearings (8) on the slider piston (9). The joints between the bearings must align with the pin hole (PH) in the slider piston. 4 311609C Kit Installation 9 12 Place clean rag over slider cylinder (2). Apply antiseize lubricant to screw (5) threads. Torque key-side screw to 210-230 ft-lb (283-310 N·m) first, then torque gap side screw to 210-230 ft-lb (283-310 N·m). 5* 38 12 39 9 ti9224b FIG. Ensure that the collars (13) are in place in the coupling nut (14). wrench on the flats of the slider piston (9*), to keep it from turning when you are tightening the coupling nut (14). [. . . ] In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise. FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées. Graco Information For the latest information about Graco products, visit www. graco. com. TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor. [. . . ]