User manual GRACO GCP3R3

[. . . ] Dispense Gun Probler P2 Elite For use with non-flammable foam and polyurea. Not for use in explosive atmospheres. 90-110 psi (0. 62-0. 76 MPa, 6. 2-7. 6 bar) Air Inlet Pressure Range 3200 psi (22 MPa, 220 bar) Maximum Static Fluid Pressure Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. USER MANUAL Models: GCP3RA GCP3R0 GCP3R1 GCP3R2 GCP3R3 GCP3R4 GCP3R5 US Patent 6, 796, 461 7, 527, 172 r_gcp3ra_313266_1_1e Table Of Contents Section 1 Installation Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To achieve the optimum spray pattern for each application, the appropriate mixing chambers are available in seven sizes. The standard mixing chamber supplied with your gun will be adequate for all but the smallest and largest applications. Foam rise and cure times will vary according to the material and substrate temperature. Higher material or substrate temperature will increase rise and cure times; lower material or substrate temperatures will decrease rise and cure times. Consult your chemical manufacturer's data specification sheets for their recommended spray temperatures. Under most circumstances, both components will be used at identical temperatures. Higher pressures and temperatures may be used to increase material break-up, improve mixing and speed rise times. With hose lengths over 50 ft. (15. 25 m), or when material viscosities are high, higher material pump pressures may be necessary. The gun air valve MUST BE OPENED prior to spraying to provide air for trigger operation and purge air when the trigger is released. When spraying, the gun trigger may be depressed continuously, or triggered at the end of each stroke. A smooth, even layer is best achieved by moving the gun back and forth in a slow, even motion, overlapping the previous pass about 50 to 75 percent. The ideal gun-to-surface distance is about 18 to 24 inches. Be sure to point the gun directly at the surface to be sprayed. Spraying at an angle to the surface will cause the foam to be rough and will generate overspray. 12 1 Apply permanent thread locker and torque to 35-40 in-lbs (4-4. 5 N·m). 2 Apply liberal coating of lubricant to seals and surfaces specified. 3 Adjust counter-clockwise until it bottoms out. Part GCP3RA GCP3R0 GCP3R1 GCP3R2 GCP3R3 GCP3R4 GCP3R5 A GC250A GC2500 GC2501 GC2502 GC2503 GC2504 GC2505 B GC251A GC2510 GC2511 GC2512 GC2513 GC2514 GC2515 Kit GC1948 GC1947 GC1947 GC1947 GC1947 GC1949 GC1949 32 44 59 A 17 B 31 14 50 37 49 27 25 47 48 1 65 20 64 46 18 29 39 42 17 28 61 1 23 65c 43 63 54 57 r_gcp3ra_313266_1_2e 26 34 52 58 36 5 4 40 8 38 Section 3 - General Information: P2 Elite Dispense Gun 13 13 41 30 42 39 22 41 12 1 65a r_257826_313213_1_1b 52 51 45 58 29 19 41 60 13 56 r_gcp3ra_313266_1_4e 3 65f 2 65e 2 65d 1 24 r_gcp3ra_313266_1_3e 65b Section 3 - General Information: P2 Elite Dispense Gun 10 56 24 12 23 61 53 56 11 62 61 15 21 9 62 14 3 2 r_gcp3ra_313266_1_5e Section 3 - General Information: P2 Elite Parts List Ref. 1 2 3 4 5 7I 8 9 10 11 12 I 13 14 15 16 v 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 34 36 37 38 39 40 41 42 GC0712 GC1198 GC1842 GC2394 GC1880 GC1881 GC1882 GC1883 GC1884 GC1885 GC1886 GC1887 GC1898 GC1899 GC1900 GC1904 GC2494 GC2495 GC1914 GC2499 GC1918 GC1920 GC1921 GC1922 GC1923 GC2496 GC2498 111450 GC0259 GC0275 GC0490 GC0502 Part GC0024 117634 117635 GC0043 GC0044 Description PIPE PLUG SWIVEL HOSE FITTING SWIVEL HOSE FITTING O-RING O-RING HEATED HOSE COVER 1/4 IN. BALL FITTING ELBOW FITTING FITTING TUBING, 1000 PSI; NYLON ELBOW FITTING LUBE FITTING BALL VALVE SWIVEL FITTING P2-ELITE HEAD P2 ELITE POLY SIDE BLOCK P2 ELITE ISO SIDE BLOCK PISTON SPACER HOSE MOUNTING PLATE PUSHLOCK SWIVEL ADAPTER WHIP HOSE WHIP HOSE AIR PISTON AIR PISTON CYLINDER SPACER CHECK VALVE FILTER SEAL, ACETAL SEAL HOUSING AIR CAP MACHINED HANDLE TRIGGER PISTON TRIGGER PLUG RETAINING RING SPRING SPRING FILTER SCREEN; 40 MESH 100 MESH FILTER (GC2497) ALSO AVAILABLE SIDE SEAL O-RING Qty. 3 1 1 2 2 2 2 1 1 1 3 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 1 1 1 1 2 2 2 2 2 Ref. 43 44 45 46 47 48 49 50 51 52 53 I 54 56 57 58 59 60 61 62 63 64 65 Part 117517 C20988 GC2056 GC2058 108833 107563 GC2059 C20207 GC2060 GC2081 GC2187 GC2212 GC2237 GC2241 GC2244 GC2248 GC2334 GC2337 GC2340 GC2341 258761 Description O-RING O-RING O-RING O-RING O-RING O-RING O-RING O-RING O-RING SET SCREW HEX NUT; 9/16-27 SCREW FITTING SHOULDER SCREW SET SCREW SET SCREW SCREW FITTING BALL VALVE TRIGGER SPRING PISTON LOCK ASSEMBLY Qty. 1 1 1 3 1 1 1 1 1 11 2 2 2 1 2 1 4 2 2 1 1 1 Ref. 65a 65b 65c 65d 65e 65f Part No. Description AIR CAP STOP SHAFT PISTON STOP COMPRESSION SPRING O-RING ADJUSTMENT NUT Qty. 1 2 1 1 1 1 Included with kit 258762. v Not Shown. 15 Section 3 - General Information: Maintenance WARNING Before attempting to perform any maintenance on this gun, relieve All Fluid and Air Pressures!· · · · · · To relieve fluid and air pressures: Turn OFF all air supplies at system except gun trigger air. Trigger the gun until all fluid pressures have been relieved. [. . . ] If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation. THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. Graco's sole obligation and buyer's sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. [. . . ]