User manual GRANDSTREAM GXW410X

[. . . ] Grandstream Networks, Inc. Analog IP Gateway GXW410x 4 or 8 FXO Ports w/Video Surveillance GXW410x User Manual Firmware Version 1. 0. 1. 2 www. grandstream. com support@grandstream. com TABLE OF CONTENTS GXW410X USER MANUAL WELCOME. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Gateway GXW410x Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety Compliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Other options are: " Always check for New Firmware. " " Check New Firmware only when F/W pre/suffix changes" " Always skip the Firmware check" If set to Yes, config file is authenticated before acceptance. This protects the configuration from an unauthorized change. The IP address or URL of System log server. This feature is especially useful for ITSP (Internet Telephone Service Provider) Select the ATA to report the log level. The level is one of DEBUG, INFO, WARNING or ERROR. Syslog messages are sent based on the following events: 1. product model/version on boot up (INFO level) 2. sent or received SIP message (DEBUG level) 4. inbound and outbound calls (INFO level) 6. registration status change (INFO level) 7. SLIC chip exception (WARNING and ERROR levels) 10. memory exception (ERROR level) The Syslog uses USER facility. In addition to standard Syslog payload, it contains the following components: GS_LOG: [device MAC address][error code] error message Example: May 19 02:40:38 192. 168. 1. 14 GS_LOG: [00:0b:82:00:a1:be][000] Ethernet link is up Authenticate Conf File Syslog Server Syslog Level NTP server URI or IP address of the NTP (Network Time Protocol) server, which will be used by the phone to synchronize the date and time. If set to Yes, the NTP server will originate from the DHCP server. Allow DHCP Option 42 to override an NTP server Enable Video Surveillance When set to Yes, GXW410x will start converting video feed received from analog camera to IP packets. In order to view this video feed, please follow instructions given under Video Surveillance chapter on page 23. By default it is 554. RTSP Port Grandstream Networks, Inc. GXW410x User Manual Firmware 1. 0. 1. 2 Page 18 of 32 Updated: 09/2007 CONFIGURING THE FXO CHANNELS Configuring the FXO channels on the GXW ­ 410x is an easy process. The Device Status page terms are defined in Table 9: FXO Lines Configuration Definitions. An example of the Channel Dialing Configuration is shown in Figure 6. Please note the default is always configured. The user has the option to change the default settings as described in the Table 9. TABLE 9: FXO LINES CONFIGURATION DEFINITIONS Enable Current Disconnect When set to Y, Current Disconnect is enabled. Certain PSTN Cos require this to be enabled, in order to realize disconnect signal from PSTN side. [. . . ] During this stage, the GXW410x's LED will blink until the checking/downloading process is completed. Upon verification of checksum, the new code image will be saved into the Flash. If TFTP fails for any reason (e. g. , TFTP server is not responding, there are no code image files available for upgrade, or checksum test fails, etc), the GXW410x will stop the TFTP process and simply boot using the existing code image in the flash. Firmware upgrading may take as long as 20 minutes over the Internet, or just 20+ seconds if it is performed on a LAN. [. . . ]