User manual GRASS VALLEY JUPITER CM-4400 VERSION 7.9.0 - 10-2010

[. . . ] JUPITER CM-4400: AccuSwitch Control System Installation and Operating Manual Software Version 7. 9. 0 071876600 OCTOBER 2010 Affiliate with the N. V. KEMA in The Netherlands CERTIFICATE Certificate Number: 510040. 001 The Quality System of: Thomson Inc, and it's wordwide Grass Valley division affiliates DBA GRASS VALLEY Headquarters 400 Providence Mine Rd Nevada City, CA 95959 United States Kapittelweg 10 4827 HG Breda The Nederlands Rue du Clos Courtel CS 31719 35517 Cesson-Sevigné Cedex France 40 Rue de Bray 2 Rue des Landelles 35510 Cesson Sevigné France Carl-Benz-Strasse 6-8 67105 Schifferstadt Germany 15655 SW Greystone Ct. Beaverton, OR 97006 United States 7140 Baymeadows Way Ste 101 Jacksonville, FL 32256 United States 1 rue de l'Hautil Z. I. des Boutries BP 150 78702 Conflans-Sainte Honorine Cedex France Spinnereistrasse 5 CH-5300 Turgi Switzerland 10 Presidential Way Suite 300 Woburn, MA 01801 United States 2300 So. [. . . ] A dash ("-") entry in the S-T field means "none. " The board types that can be selected are "VM" and "SI. " A Password level can be entered in the Password field for the output. This option is described in Setting Password Levels for Switcher Outputs on page 147. 168 JUPITER CM-4400 Control Module Installation and Operating Manual Switcher Output Table Entering or Editing Output Names and Numbers In most cases, you will want to modify the set that is currently active; if so, you may want to copy the active set and select the copy for editing. For more information, please see Copying a Configuration Set for Editing on page 130. Note On the top of the Jupiter Configurator window on the title bar, you will see the name of the Configuration set. Check to see whether the configuration set that you want to change is selected. Follow these steps to enter Output names and numbers: 1. Select the Switcher Output option from the Jupiter menu (Jupiter> Switcher Output). The Switcher Output table will then open. Enter/edit the preferred logical name and physical output numbers for this output. Note Mars physical output numbers, when controlled by a Jupiter system, are not continuous. For example, physical output numbers 8 through 15 are skipped. For more information, refer to the Crosspoint/ Jupiter control section in the Mars manual. 3. Add new inputs at the end of the tables. Row numbers on Jupiter tables are used as the logical numbers for sources. Changing the row number of an existing source on the Switcher Output table will cause panels to control different outputs than those to which they had been assigned. The memory on the controller boards will need to be cleared and reset (see Clearing Persistent Memory (PMEM) on page 106). Adding new outputs at the end of tables will help to avoid this interruption. Note Some switchers (such as Apex, late· model Trinix, Concerto, and Triton) use "1" as the first connector number. In this case, the physical output number for this connector, as entered on the table, is "0. " Connector "2" is physical output number "1, " etc. 4. Save the changes by selecting Save from the File menu (File > Save). Click the OK button to save the table. Setting Password Levels for Switcher Outputs In addition to individual Jupiter passwords assigned to each user, individual switcher outputs can be given a password level. This password can be used to provide varying levels of protection from one switcher output to another. JUPITER CM-4400 Control Module Installation and Operating Manual 169 Section 5 -- The Configurator Application Note Output passwords are not honored by automation protocol handling. In most cases, you will want to modify the set that is currently active; if so, you may want to copy the active set and select the copy for editing. For more information, please see Copying a Configuration Set for Editing on page 130. On the top of the Jupiter Configurator window on the title bar, you will see the name of the Configuration set. Check to see whether the configuration set that you want to change is selected. Follow these steps to set the password level for Switcher outputs: 1. Select the Switcher Output option from the Jupiter menu (Jupiter> Switcher Output). [. . . ] The Baud rates will be selected automatically (Figure 235). The Baud rate can be changed by clicking the drop-down list in the Baud rate column. Figure 239. The P8R (SW-P-08 Router Control) Protocol on The Serial Protocol Table Protocol Baud Rate 5. Click the Apply button and then save your changes. [. . . ]