User manual GRASS VALLEY JUPITER CONTROL SYSTEM RELEASE NOTES V7.9.0

[. . . ] JUPITER CONTROL SYSTEM Release Notes Software Version 7. 9. 0 071827513 NOVEMBER 2010 Affiliate with the N. V. KEMA in The Netherlands CERTIFICATE Certificate Number: 510040. 001 The Quality System of: Thomson Inc, and it's wordwide Grass Valley division affiliates DBA GRASS VALLEY Headquarters 400 Providence Mine Rd Nevada City, CA 95959 United States Kapittelweg 10 4827 HG Breda The Nederlands Rue du Clos Courtel CS 31719 35517 Cesson-Sevigné Cedex France 40 Rue de Bray 2 Rue des Landelles 35510 Cesson Sevigné France Carl-Benz-Strasse 6-8 67105 Schifferstadt Germany 15655 SW Greystone Ct. Beaverton, OR 97006 United States 7140 Baymeadows Way Ste 101 Jacksonville, FL 32256 United States 1 rue de l'Hautil Z. I. des Boutries BP 150 78702 Conflans-Sainte Honorine Cedex France Spinnereistrasse 5 CH-5300 Turgi Switzerland 10 Presidential Way Suite 300 Woburn, MA 01801 United States 2300 So. [. . . ] The Serial Protocol table will then open (Figure 3). 14 JUPITER -- Release Notes Pro-Bel SW-P-08 Protocol Figure 7. Example of the Serial Protocol Table 2. Double-click the protocol box that is associated with the Serial port. A drop-down list will show the possible protocol types. Select the P8R (SW-P-08 Router Control) protocol. Click anywhere in the table accept the entry. The Baud rates will be selected automatically (Figure 4). The Baud rate can be changed by clicking the drop-down list in the Baud rate column. Figure 8. The P8R (SW-P-08 Router Control) Protocol on The Serial Protocol Table Protocol Baud Rate 5. Click the Apply button and then save your changes. Compile and activate the Configuration set. JUPITER -- Release Notes 15 Version 7. 9. 0 Pro-Bel SW-P-08 Interface Implementation Notes P8R (SW-P-08 Router Control) The P8R (SW-P-08 Router Control) driver will send the following: Table 3. P8R(SW-P-08 Router Control) driver Sent Information Message CONNECT CONNECT_EXT Value 2 (matrix=pLvl/16, level =pLvl%16 input < 1024 output < 1024) 130 (depending on the input and output >= 1024) This P8R (SW-P-08 Router Control) driver will receive the following: Table 4. P8R(SW-P-08 Router Control) driver Received Information Message CONNECTED CONNECTED_EXT 4 132 Value When the P8R (SW-P-08 Router Control) driver is used, the following will occur: · The Commands that are not extended will truncate the Matrix and the Level values to a 4 bit value. The Level value in the PLvl column of the Switcher Description Table is converted into a unique Level value between 0 and 100 (0 - 0x63). The Physical level (PLvl) value is then converted into a Pro-Bel SW-P08 Matrix and Level value. The Pro-Bel SW-P-08 level value is from 0 to 15 and the Pro-Bel SW-P-08 matrix value is from 0 to 6, which is the physical level divided by 16. A Jupiter system TAKE command will send a Pro-Bel CONNECT message, which is confirmed when a CONNECTED message is received immediately following the CONNECT message. The interface will re-send a CONNECT message up to three more times after an error or if the CONNECTED response is not what was expected to confirm the TAKE command. The protocol ACKS all messages that are received correctly even if they are not implemented. · · · · 16 JUPITER -- Release Notes Pro-Bel SW-P-08 Protocol P08 (SW-P-08 Control Panel) The P08 (SW-P-08 Control Panel) driver will receive the following: Table 5. P08 (SW-P-08 Control Panel) Received Information Message CONNECT CONNECT_EXT INTERROGATE INTERROGATE_EXT CONNECTED CONNECTED_EXT Single source name request Single destination name request Single source name extended Single destination name extended 2 130 1 129 4 132 101 103 229 231 Value The P08 (SW-P-08 Control Panel) sends the following: Table 6. P08 (SW-P-08 Control Panel) Sent Information Message TALLY TALLY_EXT CONNECTED CONNECTED_EXT Source name response Destination name response Source name response extended Destination name response extended 3 131 4 132 106 107 234 235 Value When the P08 (SW-P-08 Control Panel) driver is used, the following will occur: · · · The control panel level value is a combination of the Pro-Bel SW-P-08 matrix and level values. The level is the matrix times 16 plus the level. [. . . ] Select the Anyone who uses this computer (all users) radio button. The Software License Agreement screen will then appear (Figure 17). Figure 17. Click the Yes button to accept the license agreement. The Setup Type screen will then appear (Figure 18). Figure 18. [. . . ]