User manual GRAUPNER ULTRA DUO PLUS 60

[. . . ] Operating Manual ULTRA DUO PLUS 60 Order-No. 6478 No liability for printing errors. Modifications reserved. 1/55 PAGE PN. OF-01 Contents A-1 A-2 A-3 A-4 A-5 A-6 A-7 A-8 A-9 0-1 0-2 0-3 1. Introduction Warnings and safety notes General notes on using the charger Recommended charge leads/polarity Charger controls /connections Using the charger for the first time Cleaning and maintenance Notes and handling of rechargeable batteries PC-Interface Features Main menu flow Control key select flow Memory and battery setup menu screen Charge setup menu flow Discharge setup screen Cycle menu screen Step charge menu screen Balancer Menü Data view screen Tyre, battery heater / battery heater screen / POWER SUPPLY Motor run-in screen Config setup screen Start select menu screen Battery select menu screen Operation menu screen Error message screen Specification Environnemental Protection Notes EU Conformity Declaration Warranty Page 3 4 5 7 8 8 9 9 12 14 15 16 17 19 22 24 25 27 29 32 34 36 38 45 46 52 53 54 54 55 2/55 PAGE A-1. [. . . ] _50°C TRICKLE CHG __OFF DISCHARGE _ON IMPULSE CHG 1 2 3 REFLEX CHG 123 . . . 3x STEP CHARGE <1/2> D: ON d 3mV/C 50°C . . . 5x STEP CHARGE <2/2> PEAK SENS _5mV/C CUT-TEMP. _50°C TRICKLE CHG __OFF DISCHARGE _ON IMPULSE CHG 1 2 3 REFLEX CHG 123 400 1600 3800 4500 4. 0A 8. 0A 6. 0A 4. 0A Page 25/55 5. STEP CAPACITY - This mode is only for NiMH battery, which are discharge before charging. Never charge full batteries in this mode. Use the temperature sensor for safety reasons. - Set wanted charge capacity in each step. - Step charge should be finished at the fourth step based on the selected capacity in the fourth step. Set max possible capacity which can be charged to battery. If battery is 4300mAh and 4800mAh is charged, set 4900mAh ( 100mAh ­ - If you want three step charging, make sure to set same capacity in 2 be jumped directly from 2 step to 4 step. - Value can be automatically set pressing the dial long as AUTO SETUP. STEP CURRENT - Set wanted charge current in each step. - Value can be automatically set pressing the dial long as AUTO SETUP. - The selected peak sens voltage is checked in each step. CUT-TEMP - Connect the temp sensor to battery, and charge is finished when it reaches the selected temp. - This function is likely to be used more to prevent battery pack from being overheating rather than normal charge completion 5-5. TRICKLE CHG - Set additional current after fast charging. DISCHARGE - Set whether discharge is first activated before step charging. - If "ON" is set, discharge is done based on selected capacity (max selected capacity) x 4C rate. limited to 10. 0A if X4C rate is over 10. 0A. - Step charge is basically to charge full discharged battery pack, please make sure to set "ON" always. [. . . ] Remove batteries from your device and dispose of them at your local collection point for batteries. In case of R/C models, you have to remove electronic parts like servos, receiver, or speed controller from the product in question, and these parts must be disposed of with a corresponding collection point for electrical scrap. If you don't know the location of your nearest disposal centre, please enquire at your local council office. EU Conformity Declaration We hereby declare that the following product: ULTRA DUO PLUS 60; Order-No. 6478 conforms with the essential protective requirements as laid down in the directive for harmonising the statutory directives of the member states concerning electro-magnetic interference (89/336/EWG) and LVD (73/23/EG). [. . . ]