User manual GRUNDIG MUSIC BOY 40 RP 4200

[. . . ] SER ICE ! AC~ ENGLISH LIFT Information This device is noise-suppressed according to the applicable EU directives. This product fulfils the European directives 89/336/EEC, 73/23/EEC and 93/68/EEC. This device conforms to the safety regulation VDE 0860 and therefore the international safety regulation IEC 65. Technical data Power supply: Max. [. . . ] Important: The wires in the mains lead are colour coded in accordance with the following code: BLUE ­ NEUTRAL BROWN ­ LIVE As the colours of the wires in the mains lead of your appliance may not correspond with the coloured marking identifying terminals in your plug, proceed as follows: Connect the BLUE coloured wire to plug terminal marked with the letter "N" or coloured black. Connect the BROWN coloured wire to the plug terminal marked with the letter "L" or coloured red. In no circumstance must any of the wires be connected to the terminal marked with the letter "E", earth symbol "z", coloured green, or green & yellow. Replacement mains lead sets can be obtained from your local dealer, or by contacting Grundig Consumer Relations (01788 570088) Moulded 3-pin lead set, suitable for UK use: Ref: Leadset UK 8290-991-224 8 Moulded 2-pin Euro lead set, not suitable for UK use: Ref: Leadset Euro 8290-991-316 OVERVIEW ___________________________________________ ON/OFF TONE MUSIC BOY 40 PORTABLE RADIO FM 88 92 100 104 106 108 MHz TUNING + VOL. MW 540 600 700 800 1000 1200 1400 1600 kHz SW 6 6. 5 7 8 10 12 14 16 18 kHz AC~ Controls on the top ON/OFF TONE LIFT Switches the device on and off. For raising the telescopic antenna (FM and SW reception). Controls on the front FM MW SW Station and waveband scale. Controls on the sides +VOL. Earphone socket (3. 5 mm stereo plug); Mono playback via earphones. For tuning to a radio station. SW·MW·FM Waveband switch: switches between the wavebands FM (UKW), MW (medium wave) and SW (short wave). Controls on the back AC ~ Connection socket for power cable supplied. Handle. SW MW FM ENGLISH LIFT 9 POWER SUPPLY ___________________________________ Mains operation Note: Check that the mains voltage on the type plate (on the bottom of the device) corresponds to your local mains supply. If this is not the case, contact your specialist dealer. 1 2 AC~ Plug the mains cable supplied into the »AC ~« socket on the device. Plug the mains cable into the socket (230 V~, 50/60 Hz). Note: If there are batteries in the device, these are switched off automatically during mains operation. Caution: The only way to disconnect the device from the mains supply is to pull out the plug. AC~ 10 LIFT LIFT Battery operation You can also operate the device using standard batteries (not supplied). In this case, you must disconnect the mains power cable. 1 2 Open the battery compartment by pressing the marked area and pushing down the cover. Insert four batteries (4x1. 5 V, Type IEC, AM2, LR 14, C-size) according to the polarity marked on the battery compartment. [. . . ] Glynitveien 25, Postboks 234 N-1401 Ski +47/64 87 82 00 GRUNDIG DANMARK A/S Lejrvej 19 DK-3500 Værløse +45/44 48 68 22 GRUNDIG OY Luoteisrinne 5 SF-02271 Espoo +3 58/9-8 04 39 00 GRUNDIG SVENSKA AB Albygatan 109 d, Box 4050 S-17104 Solna +46/8-6 29 85 30 GRUNDIG POLSKA SP. Z. O. O. Czéstochowska 140 PL-62800 Kalisz +48/62-7 66 77 70 GRUNDIG AUSTRIA Ges. m. b. H. Breitenfurter Straße 43-45 A-1120 Wien +43/1-81 11 70 GRUNDIG NEDERLAND B. V. [. . . ]