User manual GTO PRO AUTOMATIC GATE LOCK

[. . . ] Depending upon the installation, the gate post may need to be "pocketed" to accommodate the lock receiver. Contact the GTO Technical Service Department at (850) 575-4144 for assistance. Be sure you have all the parts: ABCDEFGHIJKLLock with 20' of low voltage wire Lock Receiver Clevis Pin Locking Cap Lock Board Battery Lead Wires White Wire (motor lead to lock board) Lock Control Board 2 Double Spade Tongue terminals 6 nylon cable ties Wire Connector Lock Keys (for manual release) Lock Decal C B A D I L K G J AUTOMATIC GATE LOCK ® E H F What else do you need? Mounting hardware is not included. Read these instructions completely and review the installation examples to determine the mounting hardware required for your application. NOTE: The GTO Lock is designed to use mounting hardware up to 5/16" in diameter. [. . . ] Also, the lock should have a solid surface or cross member to provide stability. Clamp receiver and lock together (with receiver pin hole and lock slot aligned) to the gates, mark their positions to drill holes (see Illustration E and F, page 6). The receiver must be mounted on the SLAVE GATE with carriage bolts, not U-bolts, to allow lock to seat properly. Recheck the lock's position and alignment. Drill the holes on gate supports through the slots in the lock bracket. U-bolts and saddles can be used to mount the lock on chain link gate supports. Install clevis pin and locking cap by placing clevis pin through slots in lock receiver and hammering the clevis pin into the locking cap (see Illustration G), secure the lock bracket and check the alignment again. Step 2: Step 3: (second gate opener) SLAVE GATE (first gate opener) MASTER GATE Lock and receiver must be level and aligned with opener. Receiver pin hole and lock slot must line up. Check alignment with pin out of receiver. 5 Illustration E Remember to check the alignment and mark positions before drilling holes in fence post and gate. Clevis Pin GTO Automatic Gate Lock Receiver Locking Cap Carriage bolts, washers, and nuts (not provided; size of fasteners depends on the gate) Illustration F Remember to check the alignment and mark positions before drilling holes in fence post . Added cross member to support lock from force of slammimg shut Illustration G Locking Cap Assembly Clevis Pin Receiver Lock Locking Cap U-bolts, saddles & nuts (not provided) 6 Connecting the Lock to the Opener Control Board: IMPORTANT: All Mighty Mule® and GTO/PRO® gate opener control boards manufactured since March 2000, have terminal strip wire connections (see Illustration H). If your gate opener doesn't have terminal strip connectors, you will need to follow the instructions for "Wiring the Lock to Pre-March 2000 Gate Opener Control Boards". PLEASE NOTE: If a diagram of your control board is not pictured on page 8 or 10 please call the GTO ServiceDepartment at (800) 543-1236 or (850) 575-4144 for assistance. Illustration H Terminal Strips Wiring the Lock to Pre-March 2000 Gate Opener Control Boards NOTE: If your gate opener control board has terminal wiring strips, skip to page 9 and follow the instructions for "Wiring the Lock to Gate Opener Control Boards with Terminal Strips". Step 1. Turn control box power switch OFF and unplug the transformer or disconnect the solar panel. Remove control box cover and disconnect battery lead wires from the battery terminals before wiring the lock board to the opener control board. Connect the WHITE wire (included) to Terminal #1 on the lock board. Connect the RED battery lead wire (included) to Terminal #5 on the lock board. Connect the BLACK Battery lead wire (included) to Terminal #2 on the lock board. DO NOT connect lock board battery lead wires to battery until Step 7!Lock Board Wiring Chart * Place a dab of petroleum jelly on the terminal contacts to prevent corrosion. Lock Board 12 345 RED Wire To Battery Positive (+) Terminal RED Wire From Lock BLACK Wire From Lock WHITE Wire to Motor Lead BLACK Wire To Battery Negative (­) Terminal Step 3. Attach the RED control board battery lead wire to one spade tongue on a double spade tongue connector (included). Attach the BLACK control board battery lead wire to one spade tongue on the other double spade tongue connector (included). Place the WHITE wire from the lock board inside the "blocked" channel on the Wire Connector. If the gate opens into the property (pull-to-open), place the BLACK wire from the opener power cable inside the "through" channel on the Wire Connector. Crimp the Wire Connector closed with pliers and fold plastic locking tab into place until it locks shut. 7 NOTE: If the gate opens away from the property (push-to-open) place the RED wire from the opener power cable inside the "through" channel on the Wire Connector. Crimp the Wire Connector closed with pliers and fold plastic locking tab into place until it locks shut. [. . . ] This warranty shall be considered void if damage to the product(s) was due to improper installation or use, connection to an improper power source, or if damage was caused by lightning, wind, fire, flood, insects, or other natural agent. After the one (1) year warranty period, GTO, Inc. or one of its authorized service centers will make any necessary repairs for a nominal fee. Call GTO at (850) 575-4144 for more information. [. . . ]