User manual GTO PRO-SL 1000

[. . . ] FOR VEHICULAR SLIDE GATES INSTALLATION MANUAL FOR THE PROFESSIONAL INSTALLER AUTOMATIC GATE OPERATOR This equipment is similar to other gate or door equipment and meets or exceeds Underwriters Laboratory Standard 325 (UL 325). However, gate equipment has hazards associated with its use and therefore by installing this product the installer and user accept full responsibility for following and noting the installation and safety instructions. Failure to follow installation and safety instructions can result in hazards developing due to improper assembly. You agree to properly install this product and that if you fail to do so GTO, Inc. [. . . ] Tighten set screws against exposed end of wires (see Illustration K). A dab of household petroleum jelly on each wire end will help prevent corrosion. The ACCESSORY terminal block provides the connection point for safety loops, wands, push buttons, intercoms, card readers, etc. See page 27 for more information about connecting accessories. Correct Wrong Wrong Wire Terminal Block Wire Terminal Block Wire Terminal Block BLU RED BLK POWER IN FIRST OPERATOR SECOND OPER RED BLACK Power Cable from First Operator Low Voltage Wire from AC Transformer SURGE PROTECTOR Transformer HINT: Keep a few mothballs in the control box to discourage insects from entering it and damaging the control board. STEP 13: Plug the transformer into the electrical outlet. Check to see if the green LED on the control board is on. If it is not, see the Troubleshooting Guide on page 30. NOTE: Use of a surge protector is strongly recommended. 19 RE 18VAC SOLAR ~~­ + CLS EDG ORG GRN OPN EDG CONTROL BOARD SETTINGS DIP SWITCHES The four DIP switches on the control board match the operator with the type of gate on which it is mounted. For example, gates may open right to left or left to right. Prior to packaging, the GTO/PRO SL-1000 and SL-2000 series control board was configured for a single slide gate that opens right to left. If your gate type matches this configuration, you DO NOT need to adjust the DIP switches. Proceed to the Potentiometers section on the next page. NOTE: The direction a gate opens is determined by standing inside the property and facing toward the gate. NOTE: To change the DIP switch settings, you must turn the control box power switch OFF; move the switch; then turn the power back ON. Use a small screwdriver to move the switches. PULL/PUSH: Set to PULL for slide gates that open RIGHT to LEFT [factory setting]; PUSH for slide gates that open LEFT to RIGHT. PULL/PUSH SNGL/DUAL SEQ1 SNGL/DUAL: Set to SNGL for a single gate leaf [factory setting]; SEQ2 DUAL for dual gate leaves. SEQ1: Controls the opening order of dual gate leaves. See Setting the Control Board for Dual Gate Operator Installation on page 37 for more information. SEQ2: Controls the opening order of dual gate leaves. See Setting the Control Board for Dual Gate Operator Installation on page 37 for more information (the factory setting is OFF). ON DIP switches OBSTRUCT SENS. 1234 MIN MAX LEARN LOSE AUTOC 60 ­ W. S STATUS OFF 120 + BATT INERTIA MAX MIN UCT OBSTRS. SEN USH PULL/P L UA SNGL/D SEQ1 SEQ2 MIN MAX LEARN G RB OPN EDG CLS EDG OPN EDG CLS EDG RED BLK ORG BLU GRN GRN ORG BLU WHT ORG BLU GRN RED BLK SOLAR 18VAC ­ + ~~ SECO FIRS R RATO T OPE N RATO D OPE R ALAR M S ACCE SORY RCVR R IN POWE 20 POTENTIOMETERS The three (3) potentiometers on the control board operate like a volume control on a radio. [. . . ] America's DIY Automatic Gate Openers is a trademark of GTO, Inc. and are the exclusive property of GTO, Inc. All rights are reserved by GTO, and these marks may not be used, in any for without the prior, written permission of GTO. 39 GTO PRO SL-1000 and SL-2000 series automatic gate operators are intended for use with vehicular slide gates. These operators can be used in Class I, Cass II and Class III applications. [. . . ]