User manual GTO PRO-SL 51006100

[. . . ] INSTALLATION INSTRUCTIONS FOR GTO/PRO SL-5100 and GTO/PRO SL-6100 Advanced AC Powered Slide Gate Operators LI US STED WARNING! · READ ALL INSTRUCTIONS COMPLETELY before attempting installation and use; failure to do so may result in serious injury or death!· This unit must only be installed by an experienced technician!Contact with gate operator circuitry can cause serious injury or death!Operator power must be disconnected before servicing! [. . . ] Using a fingertip, roll the limit nuts along the travel shaft until the correct open and closed gate positions are determined. If the gate opens from LEFT to RIGHT (see illustration below): the right limit switch adjusts the closed position. The left limit switch adjusts the open position. If the gate opens from RIGHT to LEFT (see illustration below): the left limit switch adjusts the closed position. The right limit switch adjusts the open position. Limit Adjustment Lock Limit Switch Plate Test the operator to verify that the limit switches are properly set. The operator should open and close the gate completely. After properly setting the limit switches, the control board must be set according to the operator application. The system accessories should also be connected to the control board. Lift limit switch plate to release, then adjust limit nut. Left Limit Nut OPEN position stop ­ if gate opens LEFT to RIGHT CLOSED position stop ­ if gate opens RIGHT to LEFT Right Limit Nut CLOSED position stop ­ if gate opens LEFT to RIGHT OPEN position stop ­ if gate opens RIGHT to LEFT Limit Switch Limit Switch Limit Switch Plate Travel Shaft The closer the limit nut is to the limit switch, the less distance the gate will travel to open or close. 13 ADVANCED GATE OPERATOR CONTROL BOARD T1SEC JP1 JP2 +300VDC DUAL GATE INTERFACE ­ + ­ STATUS LED RX 24VDC ACCES. PWR. + AUX 2 ALARM LOCK 2 LOCK 1 ­ TX + QC1 QC2 GRN GTO RED RCVR. BLK DANGER HIGH VOLTAGE 400 Volts DC ­ for 5 minutes after power is turned off! EDGE 6 EDGE 5 EDGE 4 (Not Actual Size) BATT­ BATT TEMP T1-P-CT F1 Replace with 1/2 Amp Max EDGE 3 LEARN/RESET CLS. SENS. PWR OK TIMER ON OBSTRUCT MIN MAX EDGE 2 EDGE 1 OPN. SENS. COM COM BATT+ CLOSE MAX TIME SENSOR ERR. INTERN. ERR. MIN MAX 1 MIN MAX COM OPEN INERTIA TIMER 120 FIRE DEPT. LOOP GTO Inc. , Tallahassee, FL SWNG/SLD MAST/SLV GATE R/L SEQUENC 1 SEQUENCE 2 TMR. OFF/ON NORM/LEARN OPEN/CLOSE 1 2 3 4 5 6 7 8 SAFETY LOOP COM ENTRY LOOP ON FREE EXIT COM CYCLE BATT SW 24AC 24CT 24AC 14 CONTROL BOARD SETTINGS THESE SETTINGS SHOULD BE ADJUSTED ONLY BY AN EXPERIENCED INSTALLER OR TECHNICIAN!LEARN/RESET: 1) Use to set transmitter code in control board memory. 2) Press this button to clear the diagnostic and error LEDs. LEARN/RESET ON SWNG/SLD MAST/SLV GATE R/L SEQUENC 1 SEQUENCE 2 TMR. OFF/ON NORM/LEARN OPEN/CLOSE GTO Inc. , Tallahassee, FL SWNG/SLD (swing or slide gate operation): SWNG = swing gate SLD = slide gate [factory default is SLD]. MAST/SLV (master or slave unit): This DIP switch must be set to MAST for single gate applications. For dual gate applications set one control board to MAST and the other to SLD [factory default is MAST]. See installing a Dual System on pages 22-23. GATE R/L (gate opens right or left): The direction a gate opens is determined by standing inside the property and facing toward the gate. [. . . ] Products received at the factory without an RGA number will not be accepted. Replacement or repaired parts are covered by this warranty for the remainder of the warranty period or six (6) months, whichever is greater. GTO will pay shipping charges (equivalent to United Parcel Service ground rate) for return to owner of items repaired under warranty. The manufacturer will not be responsible for any charges or damages incurred in the removal of the defective parts for repair, or for the reinstallation of those parts after repair. [. . . ]