User manual GTO PRO-SW 2000

[. . . ] ¨ + LIS TED 75 SERIES AUTOMATIC GATE OPERATOR FOR VEHICULAR SWING GATES INSTALLATION MANUAL FOR THE PROFESSIONAL INSTALLER Receiver Control Box with Battery Post Bracket Assembly 120 Volt Indoor Transformer (surge protector not supplied) Warning Sign Gate Bracket GTO/PRO 2000 Power Cable Closed Position Positive Stop Plate Run 1000' (max. ) of low voltage wire to control box from transformer. (wire not included) PVC conduit (not included) to protect wire from lawn mowers and weed eaters. WARNING! READ ALL INSTRUCTIONS CAREFULLY AND COMPLETELY before attempting to install and use this automatic gate operator. This gate operator produces a high level of force. Stay clear of the unit while it is operating and exercise caution at all times. This product meets and exceeds the requirements of UL 325, the standard which regulates gate operator safety, as established and made effective March 1, 2000, by Underwriters Laboratories Inc. 3121 Hartsfield Road · Tallahassee, Florida, USA 32303 Telephone GTO Sales: 1-800-543-GATE (4283) or (850) 575-0176 · Fax (850) 575-8912 or GTO Technical Service: 1-800-543-1236 or (850) 575-4144 · Fax (850)575-8950 1 www. gtoinc. com RB923 rev - 06/03/02 ©2000 GTO, Inc. GTO/PRO 2000 series automatic gate operators are intended for use with vehicular swing gates. [. . . ] See Dual Gate System Installation on page 40 for more information. SEQ2: Controls the opening order of dual gate leaves. See Dual Gate System Installation on page 40 for more information (the factory setting is OFF). STATUS PULL/PUSH SNGL/DUAL SEQ1 SEQ2 4 ON 1 2 3 MIN MAX LEARN LOSE AUTOC 60 W. S + BATT ­ 120 OFF INERTIA MAX MIN UCT OBSTRS. SEN MAX USH PULL/P L UA SNGL/D SEQ1 SEQ2 MIN LEARN G RB OPN EDG CLS EDG OPN EDG CLS EDG ORG BLU GRN RED BLK ORG BLU GRN GRN ORG BLU WHT BLK RED SOLAR 18VAC ­ + ~~ SECO FIRST POWE R IN N RAT D OPE OR ALAR M ACCE SSOR Y RCVR OPER ATOR 22 Potentiometers The three (3) potentiometers on the control board operate like a volume control on a radio. They control the auto close timer, inertia, and obstruction sensitivity of the operator. Use a small slotted screwdriver to turn the arrow in the center of the potentiometer. Clockwise rotation increases the setting (MAX). Counterclockwise rotation decreases the setting (MIN). AUTO CLOSE (auto close timer): Determines how long the gate will remain open before it automatically closes. INERTIA: Fine tunes obstruction sensitivity in the opening and closing modes. INERTIA allows the opener to attempt to push an obstruction clear of the gate path. When INERTIA is set to MIN the opener will obstruct quickly (i. e. , will attempt to push an obstruction briefly); when set to MAX, the opener will obstruct slowly (i. e. , will push against an obstruction for a longer period). (obstruction sensitivity): Determines the amount of force exerted by the gate on an obstruction before the operator stops and reverses. The gate will exert minimum force before obstructing when set to MIN. When set to MAX, the operator will exert maximum gate force before obstructing (i. e. , the operator will require greater resistance before stopping and reversing. ). NOTE: Heavy gates and gates with high wind resistance may require the OBSTRUCT SENS. potentiometer to be set closer to MAX to prevent the operator from obstructing. Keep in mind, however, that while you must determine the best setting for smooth gate operation, you must ALSO determine the lowest possible setting for safe gate operation. ALWAYS KEEP SAFETY AT THE TOP OF YOUR LIST WHEN ADJUSTING OR SERVICING YOUR AUTOMATIC GATE OPERATOR! AUTOCLOSE 60 OFF 120 INERTIA MIN MAX OBSTRUCT SENS. PULL/PUSH SNGL/DUAL SEQ1 SEQ2 4 ON 1 2 3 MIN MAX LEARN B G R RCVR WARNING! All three potentiometers were set to minimum at the factory. potentiometer MUST be adjusted above the factory setting for your GTO/PRO 2000 series operator to function properly. If the potentiometer is left at MIN, your gate operator may "obstruct" (i. e. , stop and reverse) as soon as it is activated. [. . . ] power cable included with GTO/PRO 2200 dual (second) gate operators. 26 Amp Hour Battery Kit (FP296) This large 12 volt, 26 ampere-hour, maintenance-free battery is for the GTO/ PRO 1000 & 2000 gate operators. It will supply additional power for increasing the number of open and close cycles. The kit comes with the battery and wiring harness for easy installation. Battery life 3 to 5 years. GTO NEMA Box (FM317) GTO's NEMA 4X rated weatherproof box is large enough (14" W x 6" D x 16" H) to accommodate all add-on items necessary for custom gate operator installations. [. . . ]