User manual HAIER 50FREE-3B

[. . . ] Fully Automatic Washing Machine User's manual This manual is for 50FREE-3B Please read this manual carefully before using. Retain it for future reference. Special number:0030805269B Packing list Contents Names of the parts 1 Safety precautions 2 Installation and adjustment 4 Install the water inlet hose 6 Preparation before washing 8 Put in the laundries 8 Add the detergent 9 Use the operation buttons 10 Close the top lid 14 Washing finished 14 Disposal after washing 15 Trouble shooting Answer to question 16 Packing list 17 Specification table the cover 2 User's manual Warranty card The side of connection between the water inlet hose and the washing machine Quantity One One One The side of connection between the jointer of the water inlet hose and the water faucet Tapping screws Eight Bottom plate One Between the upper cushion of the washing machine package and the upper seal of the package carton Inner cover component One Inside in inner tub of washing machine Automatic washing machine One Specification Water level/Water quantity (about) Water level/Water quantity (about) Max water consumption Injection pressure Rated washing spinning capacity Rated washing / / spinning capacity High/33L, Medium/22L, 4/32L 1/17L 2/21L 3/26L Low/14L 0. 03Mpa-0. 78Mpa 0. 03Mpa-1. 0Mpa 3. 0kg (weight of standard dry cloth) 3. 3kg (weight of standard dry cloth) 17 Trouble-shooting answer to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company. [. . . ] If the lint filter is lost or damaged, please contact costomer care agent of our company. Before washing, please check if the water tap is open , and if the water inlet pipe is connected properly. It is suggested to use low-foaming washing powder Dismantle Install 14 3 Installation and adjustment Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine. Install the inner cover 1. Open the top lid of the washing machine. 2. Put the inner cover component on the outer tub cover, aiming the inner cover shaft to the installation hole of the corresponding outer tub cover shaft groove. 3. Firstly insert the inner cover shaft of one side into the corresponding outer tub cover shaft groove, then push the another inner cover shaft into the corresponding outer tub cover shaft groove. Please install to designated position to guarantee there are no dropping or abnormal sound in opening and closing of the inner cover, and the operation shall be smooth. Do not dismount the inner cover component after washing. Outer tub cover Outer tub cover shaft groove Inner cover shaft Inner cover component Left hand Right hand After switching on the power, the washing machine will set to common program including"wash, rinse, spin "automatically. To select other procedures, push the " WASH", " RINSE"or "SPIN"button to select the time of wash and spin, and the times of rinse. After switching on the power, if you push one of the button among "RINSE"and"SPIN the digitron of the former procedures will turn off automatically. For instance: after switchingon the power. If you push the "SPIN" button first, it will execute spin singly after starting. Attention Even there's no water in the tub, a certain period is required before spin starting. Separate the laundries that are not colorfast from other laundries in washing. Do not use the HEAVY program for the woollen textiles. The pulsator will not rotate unless the water is filled to water level . After the machine starts operation, you can set the program and procedure during washing, set spinning time during rinsing but can not make setting in other cases. Figure 1 Figure 2 Install the bottom plate After you open the package, please lean the washing machine gently down on softitems ( like the towel cloth, blanket, etc. 1. put the drain hose up to suitable position (Do not 2. Do not step on or press the drain hose. put it on ground. ) Notes: The highest point of drain pipe shuold be higher than the water level of washing tub for avoiding to siphon phenomenon during drain. 2 Push the PROGRAM SELECTION button to select the suitable automatic program PROGRAM After switching on the power, the machine will set to STANDARD program automatically. To select other program, push the PROGRAM SELECTION button till the corresponding indicator is on. Refer to the PROGRAM SELECTION button in Page 11. For example: select SAVE WASH for the quick washing of QUICK wash Page11 the laundries with light dirt. 3 Push WASH RINSE suitable programs SPIN button to select 0. 7m<H<1. 2m POWER ON/OFF START PAUSE MIN 12 5 Install the water inlet hose Power On/Off button Wash remain time indicator digitron The program is selected but not on, It displays the total minutes of the program During operation of programs, it displays the remained time (minute). In case of abnormal phenomenon, it displays the abnormal symbol (see to Page 16) Page 16 1. Attach the water inlet hoses to the water faucet. ( As figure 1) NOTE: Do not over tighten. [. . . ] When the pulsator is running, the buttons of the laundries may cause noise. For the sake of discretion, please put the laundries with buttons into other laundries. Fill water to decided level. Avoid using whitener on laundries with color or pattern as they are prone to lose color. The whitener shall not touch the laundries directly. [. . . ]