User manual HAIER DDW6FSS

[. . . ] Avoid contact with skin and eyes and keep children away from the dishwasher when the door is open. Check that the detergent receptacle is empty after completion of the wash cycle. To maintain the EFFICIENCY and SAFETY of this appliance, we recommend: - call only service centres authorised by the manufacturer. - always use original Spare Parts Close-up View (Interior) This appliance complies with the following EEC directives: -73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications; - 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications. - Carefully dispose of the packing material. [. . . ] If the dishes have white streaks, turn the dosage adjuster to a lower setting. Load for 12 Standard Settings B C handles at the bottom. If the rack has side baskets, the spoons should be loaded individually into the appropriate slots. Long utensils should be placed in the horizontal position at the front of the upper rack. F How to Use the Upper Rack The upper rack is designed to hold more delicate and lighter dishware, such as glasses, cups and saucers, as well as plates, small bowls and shallow pans. It is recommended that dishes placed in the upper rack are not too dirty . Position the dishes and cookware so that they do not get moved by the spray of water. The upper rack can be adjusted for height by using the knobs located on the sides of the rack itself (see fig. 3 4 1 2 NOTE: To facilitate closing the cover, remove any excess detergent on the edges of the dispenser. C fig. A fig. B . 3. GB GB . 4. Turning on the Appliance Energy Saving Tips Starting a wash cycle - Make sure that the plug for the appliance is inserted into the wall socket. - Make sure that the water supply is turned on to full pressure. - Load the dishwasher (see the section entitled, "Loading the Dishwasher" on page 4). - Pour in the detergent (see the section entitled, "Detergent and Rinse Aid" on page 3). - Turn the knob located on the right of the control panel in clockwise direction until the number or symbol for the cycle setting is aligned with the reference mark (see the section entitled, "Wash Cycle Table" on page 7). - Press the POWER button, and the POWER light will turn on. At this point, the wash cycle will begin. Wait a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they are still hot and more susceptible to breakage. They will also dry better. - It is important to try and run the dishwasher when it is fully loaded to save on energy. In order to prevent odors from forming and food from caking onto the dishes, you can run the Pre-Rinse cycle. - Choose the right wash cycle: the choice of cycle depends on the type of dishware, cookware and utensils being washed and how dirty they are. - Use the right amount of detergent: if you use too much detergent, the result will not be cleaner dishes, but, rather, a greater negative impact on the environment. Cancelling or modifying a wash cycle setting A cycle that is underway can only be modified if it has been running for a short time. Otherwise, the detergent may have already been used, and the appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled (see the paragraph entitled, "Loading the Detergent" on page 3). Press the POWER button, and the ON light will turn off. Rotate the knob in clockwise direction to the desired cycle setting (see the section entitled: Starting a wash cycle ?F. [. . . ] In this case, the wash cycle time will be shortened by about 15 minutes and the wash efficiency slightly reduced. The connection must be made to the hot water line following the same procedures as those for the connection to the cold water line. Levelling the Appliance Once the appliance is positioned, adjust the feet (screwing them in or out) to adjust the dishwasher, making it level. The appliance should not be inclined more than 2 . If the appliance is level, it will help ensure proper performance. Cold Water Connection Connect the cold water supply hose to a threaded 3/4 (gas) connector and make sure that it is fastened tightly in place (see fig. 1). [. . . ]