User manual HAIER DW9-LBE

[. . . ] To maintain the EFFICIENCY and SAFETY of this appliance, we recommend: - call only the Service Centers authorized by the manufacturer. - always use original Spare Parts This appliance complies with the following EEC directives: -73/23/EEC of 19 February 1973 (Low Voltage) and subsequent modifications; - 89/336/EEC of 3 May 1989 (Electromagnetic Compatibility) and subsequent modifications. - Carefully dispose of the packing material. - After removing the packing, check to make sure that the appliance is not damaged. If in doubt, contact a qualified professional. [. . . ] Especially long utensils should be placed in the horizontal position at the front of the upper rack. Load for 9 Standard Settings Load for 9 Standard Settings (for IEC-EN 50242 tests) How to use the upper rack The upper rack is designed to hold more delicate and lighter dishware, such as glasses, cups and saucers, plates, small bowls and shallow pans (as long as they are not too dirty). - Position the dishes and cookware so that they do not get moved by the spray of water. The upper rack can be adjusted for height by using the knobs located on both sides of the rack itself (see fig. C). Adjust the upper basket to the higher level and you have more space to accommodate those taller pans and trays in the bottom basket. fig. A fig. B Shelf Lean tall glasses and those with long stems against the shelfnot against other items to be washed. Place glasses, cups and small bowls on the additional cup rack. The additional cup rack can be swivelled in or out as required (see fig. D). fig. C fig. D Knife rack The knife rack clips onto the side of the top basket, giving you the freedom to wash your large sharp knives separately and out of harm's way (see fig. E). fig. E . 5. GB Starting the Appliance Starting a wash cycle After having completed all of the installation steps in the preceding paragraphs, turn on the water all the way and press the ONOFF button (A) located on the control pannel. The appliance is on (see fig. 1). Setting the Wash Cycle with a Delayed Start Time By pressing the "D" button (see close-up view-'Control panel"), select , and the selection cursor turns on, then pressing the "C" button , the start of wash can be delayed for between 1 to 12 hours. Each time the "L" button is pressed, the display (M) will show the number of hours for the delay period. After selecting the wash cycle, pressing the start-pause button(E), the delay time on the display will blink. This indicates that the countdown has begun. After the time has alapsed, the cycle will start. Setting and Starting a wash Cycle Select the desired cycle by pressing programme selection button (F). Each time the button is pressed, the seletion cursor"Q"will come on in succession. Choose the wash cycle you feel is most appropriate for the type of dishes that need washing (consult the wash cycle table contained in this manual. After press the startpause button(E), the wash cycle has begun and can no longer be changed. If necessary, read the paragraph entitled "Cancelling or modifying a cycle" NOTE: During the delay period, it is preferable not to change any of the settings, If this is necessary, all of the settings must be cancelled by pressing the ON/OFF button (A). At this point, all of the steps for "setting the wash cycle with a Delayed Start Time" and "Setting and Starting a wash cycle" must be repeated, following the instructions contained in the corresponding sections. If the door is opened to the unit during the delay period, the countdown will stop. It wil begin again when the door is closed. Cancelling or modifying a cycle A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the detergent may have already been used, and the appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled (see the paragraph entitled, "Loading the Detergent"). To modify a cycle that is already underway, press the start- pause button (E) for 5 second, all of the settings will be cancelled. To set a new cycle, follow the instructions contained in the paragraph entitled "Setting and starting a wash cycle". All of the wash cycle set to reverse time function, we may in focus start circulate time. Wash Cycle adjustment Buttons Button for "extre drying" or "half load" or "delay" By pressing the "D" button in sequence , the selection cursor (Q) will come on in turn : Extre drying -- Half load --Delay -- Extre drying+Half load --Extre drying+Delay --Half load +Delay -- Extre drying+Half load + Delay Extre drying By pressing the "D" button, the drying time of extre drying will be longer , and the drying relating is better. [. . . ] This hose is available upon request from specialised retailers and service centres. Levelling the Appliance Once the appliance is positioned, adjust the feet (screwing them in or out) of the dishwasher until it is level. In any case, the appliance should not be inclined more than 2°. If the appliance is level, it will help ensure proper performance. Cold Water Connection Connect the cold water supply hose to a threaded 3/4 (gas) connector and makeing sure that it is fastened tightly in place (see Fig. 1). If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the water is clear and free of impurities. [. . . ]