User manual HAIER FDI6IE1

[. . . ] If in doubt, contact a qualified professional. - The dishwasher must only be used by adults for the washing of household dishes and cooking utensils. - Fundamental rules to follow when using the appliance: * Never touch the dishwasher when barefoot or with wet hands or feet; * We discourage the use of extension cords and multiple sockets; * During installation, the power supply cord must not be excessively or dangerously bent or flattened; * If the appliance is not operating properly or maintenance must be performed, disconnect the appliance from the power supply. Notice: The appliance is not instruct for use of young children of infirm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance. [. . . ] Open the door, turn off the appliance using the ON-OFF switch and turn off the water supply to the unit. Wait a few minutes before removing the dishes so as to avoid handling them while still hot (when they are more susceptible to breakage) and to get better drying results. Very dirty dishes, Pre-wash with hot water. Extended wash at 70 Rinse with cold water. Extended wash at 50 Rinse with cold water. Extended wash at 50 Rinse with cold water. Economic, fast cycle to be used for items which are sensitive to higher. (Not to be used with delicate items) Cycle Cycle Selection Information Description of Cycle Detergent Rinse Aid Duration in minutes Setting and Starting a wash Cycle Choose the desired cycle by pressing the cycle selection button "P". Each time it is pressed, one of the cycle indicator lights "J" will come on in succession. Choose the wash cycle you feel is most appropriate for the type of dishes that need washing (consult the wash cycle table contained in this manual, especially when first using the appliance). Close the door and after a few seconds, the wash cycle has begun and cannot be modified. If necessary, read the paragraph entitled, "Cancelling or modifying a cycle while underway. "The end of the cycle will be signalled by a double acoustic sound, and the indicator light "J" will begin to blink. 30g 112 Setting The Start Delay Time Open the door of the dishwasher partially. If the "C" button is pressed (see, Close-up View" Control Panel"). The start time for the wash cycle can be delayed for 2, 4, 6, 8, 10 or 12 hours. Each time the button is pressed, the "D" light will come on indicating the length of the delay. After selecting the delay time, the wash cycle can be set, as explained in "Setting and starting a wash cycle. . . " There will be a short acoustic signal, and at this point the delay period will begin to count down. During this period the delay indicator light (D) will blink. At the end of the delay time, the indicator will stop blinking and the cycle will start. Heavy Duty 20g 94 (1/2 Load) 96 5+25g ERF 20g 82 (1/2 Load) Normal Wash Normal dirty dishes, pots and pans without dried on residue. 30g 102 90 (1/2 Load) 92 82 (1/2 Load) Cancelling or modifying a cycle while underway. . . Premise: A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the detergent may have already been used, and the appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled (see the paragraph entitled, "Loading the Detergent"). NOTE: During the delay period, none of the settings can be modified. If the ON-OFF button "A" located on the contro panel, the door is opened during the delay period, the clock will stop the countdown. [. . . ] Use the special plastic support that comes with the appliance (see fig. 2). The free end of the hose must be at a height between 40 and 100 cm and must not be immersed in water. Levelling the Appliance Once the appliance is positioned, adjust the feet (screwing them in or out) to adjust the dishwasher, making it level. In any case, the appliance should not be inclined more than 2°. If the appliance is level, it will help ensure proper performance. Cold Water Connection Connect the cold water supply hose to a threaded 3/4 (gas) connector, making sure that it is fastened tightly in place (see fig. 1). [. . . ]