User manual HAIER H2SM-18RA03/R1

[. . . ] SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL HSU-07RA03/R1(B) HSU-09RA03/R1(B) HSU-12RA03/R1(B) H2SM-18RA03/R1(B) Please read this operation manual before using the air conditioner. No. Cautions Safety Instructions and Warnings Disposal of the old air conditioner Before disposing an old air conditioner that Before starting the air conditioner, read the goes out of use, please make sure it's inopinformation given in the User's Guide careferative and safe. The User's Guide contains very imporin order to avoid the risk of child entrapment. observations relating to the assembly, tant operation and maintenance of the air conditioner. It must be noticed that air conditioner system contains refrigerants, which require specialized waste disposal. [. . . ] Press ON/OFF button, the unit stops. 5. Unit stop 11 Operation Fan Operation Remote controller 1. Unit start Link with electronic power. Press ON/OFF on the remote controller, unit starts. The liquid crystal will display the working state of last time (Except Timer, Sleep, Power/Soft and Health airflow). 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY F AN HEA T Then Select FAN operation 3. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW MED I H 4. Unit stop Press ON/OFF button, the unit stops. About FAN operation In FAN operation mode, the unit will not operate in COOL or HEAT mode but only in FAN mode , AUTO is not available in FAN mode. And temp. setting is disabled. In FAN mode, SLEEP operation is not available. 12 Operation Heat Operation 1. Press ON/OFF on the remote controller, unit starts. The liquid crystal will display the working state of last time (Except Timer, Sleep, Power/Soft and Health airflow). Remote controller 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY F AN HEA T Then Select HEAT operation 3. Select temp. setting Press TEMP. button Every time the button is pressed, temp. setting increase 1 C, if kept depressed, it will increase rapidly. Every time the button is pressed, temp. setting increase 1 C, if kept depressed, it will decrease rapidly. Select a desired temperature. 4. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW MED I H AUTO Air conditioner is running under displayed wind speed IN HEAT mode, warm air will blow out after a short period of the time due to cold-draft prevention function. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. 5. Unit stop Press ON/OFF button, the unit stops. 13 Operation Air Flow Direction Adjustment 1. Status display of air sending direction Vertical flap Pos. 1 Pos. 2 Pos. 3 Pos. 4 Pos. 5 Pos. 6 (Auto swing) 2. Up and down air flow direction For each press of swing button, air flow direction on remote controller or on the control panel displays as follows according to different operation modes COOL/DRY/FAN Pos. 2 Pos. 3 Pos. 4 Pos. 6 remote controller: Pos. 1 : HEAT remote controller: Pos. 5 : AUTO remote controller:Pos. 1 : Pos. 4 Pos. 3 Pos. 2 Pos. 1 Pos. 6 Pos. 2 Pos. 3 Pos. 4 Pos. 5 Pos. 6 The vertical flap will swing according to the above positions 3. Note: When restart after remote turning off, the remtoe controller will automatically memorize the previous set swing position. When making coolness, wind orientation should adjust to the horizontal state in favor of air circulating in the room for cool air will agglomerate upside. When making heat, wind orientation should adjust to the slanting down state in favor of air circulating in the room for hot air will agglomerate downside. 14 Operation Sleep Operation Before going to bed, you can simply press the SLEEP button and unit will operate in SLEEP mode and bring you a sound sleep. SLEEP operation starts SLEEP operation stops Use of SLEEP function A p r o x . 6 h r s After the unit starts, set the operation status, then press SLEEP button before which the Rises 1 C 1 hr clock must be adjusted and time being set. In COOL, DRY mode 1 hours after SLEEP mode starts, temp. p s t i n g become 1OC higher than temp. After In COOL, DRY mode O another 1 hours, temp. The unit will run for further 6 hours then stops. [. . . ] cloth. Do not use the following for cleaning Gasoline, benzine, thinner or cleanser may damage the coating of the unit. Hot water over 40OC(104OC) may cause discoloring or deformation. Air Filter cleaning Open the inlet grille by pulling it upward. Remove the filter. Push up the filter's center tab slightly until it is released from the stopper, and remove the filter downward. Clean the filter. Use a vacuum cleaner to remove dust, or wash the filter with water. After washing, dry the filter completely in the shade. Attach the filter. Attach the filter correctly so that the "FRONT" indication is facing to the front. Make sure that the filter is completely fixed behind the stopper. If the right and left filters are not attached correctly, that may cause defects. Once every two weeks Close the inlet grille. 22 Maintenance Replacement of Air Purifying Filter 1. Open the lnlet Grille Open the inlet grille by pushing each ends of the inlet grille upward. (use thumbs to push up) 2. Detach the standard air filter Slide the knob slightly upward to release the filter, then withdraw it. 3. Detach old Air Purifying Filter 4. Attach old Air Purifying Filter Detach old Air Purifying Filter Put air purifying filter appliances into the right and left filter frames . 5. Attach the standard air filter (Necessary installation) 6. Close the Inlet Grille Close the Grille surely NOTE: The air purifying filter of the bacteria-killing medium and the electrostatic air purifying filter accessories with machine will be used based on real situation. The bacteria-killing medium air purifying filter is available for a long time and needn't to be changed. But it must be noticed to use the vacuum cleaner frequently to adsorb the dusts covering the purifying filter lest the covering dusts effect t function of the bacteria-killing medium air purifying filter. [. . . ]