User manual HAIER H2SM-HV03-R2

[. . . ] SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL HSM09HV03/R2(DB) HSM09HV03/R2(DB) 2HUM18H03/R2(DB) HSM09HV03/R2(DB) HSM12HV03/R2(DB) 2HUM18H03/R2(DB) Please read this operation manual before using the air conditioner No. 0010557179 Cautions Disposal of the old air conditioner Before disposing an old air conditioner that goes out of use, please make sure it's inoperative and safe. Unplug the air conditioner in order to avoid the risk of child entrapment. It must be noticed that air conditioner system contains refrigerants, which require specialized waste disposal. The valuable materials contained in an air conditioner can be recycled . Contact your local waste disposal center for proper disposal of an old air conditioner and contact your local authority or your dealer if you have any question. [. . . ] (It's available under any mode) When the fan in the indoor unit does not work, the health lamp lights up, but the anion generator does not release anion. BRIEF INTRODUCTION TO HEALTH ANION FUCTION The anion generator in the air conditioner can generate a lot of anion effectively balance the quantity of position and anion in the air and also to kill bacteria and speed up the dust sediment in the room and finally clean the air in the room. 8 Operation Auto Operation Remote controller 1. Unit start Press ON/OFF on the remote controller, unit starts. 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select DRY operation On the displaying board, colorful displaying bar will be light blue 3. Select temp. setting FRESH POWER/SOFT Press TEMP. button Every time the button is pressed, temp. setting increase 1oC, if kept depressed, it will increase rapidly Every time the button is pressed, temp. setting decrease 1oC, if kept depressed, it will decrease rapidly. Select a desired temperature. 4. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW MED HI AUTO Air conditioner is running under displayed fan speed. In DRY mode, when room temperature becomes lower than temp. setting+2oC, unit will run intermittently at LOW speed regardless of FAN setting. 5. Unit stop Press ON/OFF button, the unit stops. 11 Operation Fan Operation 1. Unit start Press ON/OFF on the remote controller, unit starts. Remote controller 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select FAN operation On the displaying board, colorful displaying bar will be pink. 3. Fan speed selection FRESH Press FAN button. For each press, fan speed changes as follows: Remote controller: POWER/SOFT LOW MED HI 4. Unit stop Press ON/OFF button, the unit stops. About FAN operation In FAN operation mode, the unit will not operate in COOL or HEAT mode but only in FAN mode , AUTO is not available in FAN mode. And temp. setting is disabled. In FAN mode, SLEEP and POWER/SOFT operation is not available. 12 Operation Heat Operation 1. Unit start Press ON/OFF on the remote controller, unit starts. Remote controller 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select HEAT operation On the displaying board, colorful displaying bar will be red 3. Select temp. setting FRESH POWER/SOFT Press TEMP. button Every time the button is pressed, temp. setting increase 1oC, if kept depressed, it will increase rapidly Every time the button is pressed, temp. setting decrease 1oC, if kept depressed, it will decrease rapidly Select a desired temperature. 4. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW MED HI AUTO Air conditioner is running under displayed fan speed IN HEAT mode, warm air will blow out after a short period of the time due to cold-draft prevention function. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. 5. Unit stop Press ON/OFF button, the unit stops. 13 Operation Air Flow Direction Adjustment 1. Status display of air sending Vertical flap Pos. 1 Pos. 1 Pos. 2 Pos. 3 FRESH Horizontal louvers Pos. 2 Pos. 3 Pos. 4 Pos. 5 Pos. 4 POWER/SOFT Pos. 5 Pos. 6 (Auto swing) Pos. 6 Pos. 7 Pos. 8 2. Up and down air flow direction For each press of button, air flow direction on remote controller displays as follows according to different operation modes: COOL/DRY/FAN Pos. 1 Pos. 2 Pos. 3 Pos. 4 Pos. 6 remote controller: : HEAT: remote controller: AUTO: remote controller: Pos. 5 Pos. 4 Pos. 3 Pos. 2 Pos. 1 Pos. 6 Pos. 1 Pos. 2 Pos. 3 Pos. 4 Pos. 5 Pos. 6 The vertical flap will swing according to the above positions 3. Left and right air flow direction For each press of remote controller: Pos. 1 Pos. 2 Pos. 3 button, remote controller displays as follows : Pos. 4 Pos. 5 Pos. 6 Pos. 7 Pos. 8 The horizontal louvers will swing according to the above positions. Note:When restart after remote turning off, the remote controller will automatically memorize the previous set swing position. 14 Operation Sleep Operation Before going to bed, you can simply press the SLEEP button and unit will operate in SLEEP mode and bring you a sound sleep. Use of SLEEP function After the unit starts, set the operation status, then press SLEEP button before which the clock must be adjusted and time being set. In COOL, DRY mode 1 hours after SLEEP mode starts, temp. The unit will run for further 6 hours then stops. setting so that room temperature won't be too Iow for your sleep. SLEEP operation starts SLEEP operation stops Approx. 6hrs Rises 1OC 1 hr 1 hr Rises 1OC Temp. setting Unit stop In COOL, DRY mode Remote Controller 2. [. . . ] The photocatalyst air purifying filter will be solarized in fixed time. In normal family, it will be solarized every 6 months. The solarization time will last no less than 8 hours under the state of abundant sun. The bacteria-killing medium air purifying filter is available for a long time and neednít to be changed. [. . . ]