User manual HAIER HLH26BBTV

[. . . ] IMPORTANT SAFETY INSTRUCTIONS Read all of the instructions before using this appliance. When using this appliance, always exercise basic safety precautions, including the following: 1)Save these Instructions ---the safety and operating instructions should be retained for future reference. 2)All warning on the appliance and in the operating instructions should be followed. 3)Cleaning --- Unplug from the wall outlet before cleaning. [. . . ] Press CH+/- button to Select Woofer, press VOL+/- button to set Woofer as Off or On Note: 1. Select Balance to balance right and left sound channels of the TV. When indication value of Balance increases toward+50, sound of the right and left speaker becomes stronger and weaker, respectively. When indication value of Balance decreases toward -50, sound of the right and left speaker becomes weaker and stronger. 2. When Personal mode is not selected, the Personal mode can be entered automatically if Treble or Bass parameters are adjusted. Adjustment Setup Adjustment Setup In VGA and DVI input mode , H Position and V Position can be used to adjust the picture position. VGA/DVI: Display Mode When VGA DVI input mode is set 1. Press MENU button on the remote controller and then use the VOL+/- to select the ADJ. menu. Press the VOL+ button and then use CH+/- button for desired adjust parameter option. Press VOL+/-for desired adjust parameter option until satisfactory value is achieved. When VGA signals are received, the automatic mode is used for parameter adjustment. Full Screen Adjust RGB Reset Auto Sync. Color Temper Black Stretch A B C Standard On No selectable Note: Adjust, RGB and Reset are functional only under VGA and DVI mode, and Auto Sync is functional in VGA mode. Display Mode This will adjust the picture ratio. Under the VGA signal, there are Full Screen , one to one and 4:3 mode for Display mode to select. Under the AV1or Av2 signal, there are Full Screen, Vertical Zoom, Half Zoom, Panorama and 4:3 Mode for Display Mode to select. Under the DVI signal, there are Full Screen and 4:3 Mode for Display Mode to select. Adjust this is opted for adjusting H Position and V Position as well as relative parameters in VGA and DVI modes. (Phase Adjust is not available in DVI) RGB this is opted for adjustment of the numerical value of red, green and blue in VGA/DVI mode. Reset this is opted for initialization adjustment of parameters (After the operation, Complete will be on the right of the option) Auto sync this is opted for adjustment of picture location frequency and phase parameters in VGA mode. (Not available in DVI) ( After the operation, Complete will be on the right of the option. ) H Size H Position V Size V Position Phase Adjust A B C 0 0 0 0 0 Red Green Blue 0 0 0 A B C Color temperature This will increase or decrease Warm (red) and Cold (blue) colors to suit personal preferences. Select Cold to give the white colors a blue tint, Standard to give the white colors a neutral tint, Warm to give the white colors a red tint. Function Setup Function Setup It is possible to select Menu Language, OSD translucent, position and screen display of MENU as follows: 1. Press MENU button once, and then use VOL+/- button until the following menu appears on the screen: 2. Press the VOL+ button and then use CH+/- button on the remote controller to enter MENU of system setup. Press CH+/- to select desired option on MENU. Press VOL+/- to adjust selected option. Av Menu Language OSD Timeout English 15seconds Translucent Off Off Off Menu Language Option Repeat step 3 and 4 to select English, Francais or Espanol as MENU Menu Language. Menu Background Calendar Auto Off BlueScreen Close Caption OSD Timeout Option Repeat step 3 and 4 to select menu display time for 5, 10, 15, 20, 25, 30 or 40 seconds. Parental A B C Menu Background Option Repeat step 3 and 4 to select OSD background between Translucent and Opaque. Calendar Display and Check Repeat step 3 and press VOL+/- button to enter calendar menu as follows: Enter Calendar menu, press VOL+/- and CH+/- button to adjust or check the date. Auto Off Repeat step 3 and 4 to select On/Off. If On is selected, and there is no signal to the TV for 2 minutes , Auto Off will be on the screen and for 3 minutes the TV will be in standby condition . [. . . ] - Set every aspect ratio for Video, Component 480i sources. - Use 4:3, or 16:9 for other RGB-PC and DVI-PC sources. - Horizon is not available for Component (480p, 720p, 1080i), DTV (480p, 720p, 1080i) sources. Press the ARC button repeatedly to select the desired picture format. [. . . ]