User manual HAIER HPU-18CU13

[. . . ] SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL HPU-18CU13 HPU-20CU13 Please read this operation manual before using the air conditioner No. 0010562446 Cautions Disposal of the old air conditioner Before disposing an old air conditioner that goes out of use, please make sure it's inoperative and safe. Unplug the air conditioner in order to avoid the risk of child entrapment. It must be noticed that air conditioner system contains refrigerants, which require speciali-zed waste disposal. The valuable materials contained in an air conditioner can be recycled Contact your local waste disposal center for proper disposal of an old air conditioner and contact your local authority or your dealer if you have any question. [. . . ] Don't throw or knock the remoter controller. When electronic-started type fluorescent lamp or change-over type fluorescent lamp or wireless telephone is installed in the room, the receiver is apt to be disturbed in receiving the signals, so the distance to the indoor unit should be shorter. Loading of the battery Load the batteries as illustrated right 2 R-03 (7#) batteries Remove the battery cover: Slightly press" as illustrated. "area and push down the cover Load the battery: Be sure that the loading is in line with the "+" / "-". request as illustrated on the bottom of the case. Put on the cover again. Confirmation indicator: After pressing power ON/OFF, if no display, reload the batteries. Note: Full display or unclear display during operation indicates the batteries have been used up. Used two new same-typed batteries when loading. If the remote controller can't run normally during operation, please remove the batteries and reload several minutes later. Hint: Remove the batteries in case unit won't be in usage for a long period. If there are any display after taking-out, just need to press reset key. 8 Operation Display board HEALTH operation HEALTH TEMP Remote controller 1. Unit start Press ON/OFF button, unit starts. Health function includes health anion function, UV light degerming function. 2. Health anion function Press HEALTH button. Air conditioner starts health anion function operation. For twice press, disappears, the operation stops. When indoor fan motor is running, it has healthy process function. (It's available under any mode) BRIEF INTRODUCTION TO HEALTH ANION FUCTION The anion generator in the air conditioner can generate a lot of anion effectively balance the quantity of position and anion in the air and also to kill bacteria and speed up the dust sediment in the room and finally clean the air in the room. About UV light degerming function UV light emitted by the UV light device of the indoor unit catalytically activates the nano TiO2 on the multi-lights touching intermediary, and the degerming effect is highly efficient and lasting. button Every time the button is pressed, temp. setting increase 1oC, if kept depressed, it will increase rapidly Every time the button is pressed, temp. setting decrease 1oC, if kept depressed, it will decrease rapidly Select a desired temperature. 4. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: Ultra-low air flow COOL operation starts when room temp. is higher than temp. setting. Temp. setting+2oC Temp. setting LOW MED HI AUTO On reaching temp. setting +2oC unit will run in mild DRY mode. Air conditioner is running under displayed fan speed. In DRY mode, when room temperature becomes lower than temp. setting+2oC, unit will run intermittently at LOW speed regardless of FAN setting. 5. Unit stop Press ON/OFF button, the unit stops. 12 Operation Display board Fan Operation TEMP 1. Unit start Remote controller Press ON/OFF button, unit starts. 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN Then Select FAN operation 3. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW MED HI 4. Unit stop Press ON/OFF button, the unit stops. About FAN operation In FAN operation mode, the unit will not operate in COOL mode but only in FAN mode , AUTO is not available in FAN mode. And temp. setting is disabled. In FAN mode, SLEEP operation is not available. 13 Operation Air Flow Direction Adjustment 1. Status display of air sending Vertical flap Pos. 1 Pos. 2 Pos. 3 Pos. 4 Pos. 5 Pos. 6 the cabinet type Horizontal louvers Pos. 1 Pos. 2 Pos. 3 Pos. 4 Pos. 5 Pos. 6 Pos. 7 Pos. 8 Vertical flap Vertical flap Horizontal louvers Pos. 1 Pos. 2 Pos. 3 Pos. 4 Pos. 5 Pos. 1 Pos. 2 Pos. 3 Pos. 4 Pos. 4 Pos. 5 Pos. 6 (Auto swing) Fig. 4 Pos. 1 Pos. 2 Pos. 3 (Auto swing) Fig. 3 2. Up and down air flow direction For each press of button, air flow direction on remote controller displays as follows according to different operation modes: COOL/DRY/FAN: remote controller: Vertical flap: AUTO: remote controller: Vertical flap: Pos. 1 Pos. 1 Pos. 2 Pos. 2 Pos. 3 Pos. 3 Pos. 4 Pos. 4 Pos. 6 Pos. 5 Fig. [. . . ] Then, reinstall it onto the unit. Once every two weeks 21 Maintenance To Keep Your Air conditioner in Good Condition after Season. 1. Operate in FAN mode for about half a day. On a fine day, unit shall be started and operate in FAN mode for about half a day until the inside of the unit becomes thoroughly dry. 2. Take out the batteries from the wireless remote controller. 22 Maintenance Before Setting in High season 1. Cleaning the standard air filter. Operation without filter may cause troubles. Be sure to attach both right and left filters prior to the operation. [. . . ]