User manual HAIER HSU-108HEA03

[. . . ] Installation shall be done by professional people, don't install unit by yourself. For the purpose of the safety, the air conditioner must be properly grounded in accordance with specifications. Always remember to unplug the air conditioner before openning inlet grill. Never unplug your air conditioner by pulling on the power cord. [. . . ] SWING Used to set auto fan direction. 17. LOCK Used to lock buttons and LCD display. LOCK RESET 24 23 19. TEMP. Used to select your desired temp. 18 1. Operation mode display Operation mode Remote controller Display board COOL DRY 20. SET Used to confirm timer and clock settings. 21. TIMER Used to select TIMER ON, TIMER OFF, 22. RESET Used to reset the controller back to normal condition. 2. HEALTH Used to operate the healthy function AUTO HI MED LO 25. Ambient temp. display When receiving the remote control signal, display the set temperature and in the rest time the room temperature is displayed and this room temperature is only for reference. Clock set When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows: Press CLOCK button, "AM" or "PM" flashes. Each press will increase or decrease 1min. If the button is kept depressed, time will change quickly. After time setting is confirmed, press SET, "AM "and "PM" stop flashing, while clock starts working. NOTE: Cooling only unit do not have displays and functions related with heating The unit do not have functions related with healthing Hints After replacing with new batteries, remote controller will conduct self-check, displaying all information on LCD. Then, it will become normal. 4 Operation Remote controller's operation When in use, put the signal transmission head directly to the receiver hole on the indoor unit. The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well. Don't throw the controller, prevent it from being damaged. When electronic-started type fluorescent lamp or change-over type fluorescent lamp or wireless telephone is installed in the room, the receiver is apt to be disturbed in receivering the signals so the distance to the indoor unit should be shorter. Loading of the battery Load the batteries as illustrated. 2 R-03 batteries, resetting key (cylinder) Remove the battery cover: Slightly press " " and push down the cover. , ͬ ȡ ѡ , ʱ 7# , ҹ © , 6 ԡ ء ˾ װ ѡͬһƷ 7# , ʱ䲻ʱ, Ϊ ֹ©ҹ뽫ȡ ʹ쳣, ȡ, 6Ӻ װء ຺ ܹ˾ ѡͬһƷ 7# , ʱ䲻ʱ, Ϊ ֹ©ҹ뽫ȡ ʹ쳣, ȡ, 6Ӻ װء ຺ ܹ˾ Load the battery: Be sure that the loading is in line with the" + "/"-" pole request as illustrated. Put on the cover again Confirmation indicator: In disorderation, reload the batteries or load the new batteries after 6mins. Note: Use two new same-typed batteries when loading. If the remote controller can't run normally or doesn't work at all, use a sharp pointed item to press the reset key. Hint: Remove the batteries in case unit won't be in usage for a long period. If there are any display after taking-out just need to press reset key. Power failure resume(please set and apply as necessary) If sudden power failure occurs, the unit will resume original operation when power is supplied again. Note to the power failure resume: press the health button ten times in five seconds and enter this function after hearing four sounds. [. . . ] During unit operation or at stop, a swishing or gurgling noise may be heard. At first 2-3 minutes after unit start, this noise is more noticeable. (This noise is generated by refrigerant flowing in the system. ) During unit operation, a cracking noise may be heard. This noise is generated by the casing expanding or shrinking because of temperature changes Should there be a big noise from air flow in unit operation, air filter may be too dirty. [. . . ]