User manual HAIER HSU-10LEA03-T

[. . . ] SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL HSU-05LEA03 HSU-07LEA03 HSU-09LEA03 HSU-12LEA03 HSU-18LEA03 HSU-22LEA03 HSU-24LEA03 HSU-102LD08 HSU-122LD08 HSU-182LD08 HSU-222LD08 HSU-09LEA13-W HSU-12LEA13-W HSU-18LEA13-W HSU-22LEA13-W HSU-09LEA03-T HSU-13LEA03-T Please read this operation manual before using the air conditioner. 0010515137 Cautions Disposal of the old air conditioner Before disposing an old air conditioner that goes out of use, please make sure it's inoperative and safe. Unplug the air conditioner in order to avoid the risk of child entrapment. It must be noticed that air conditioner system contains refrigerants, which require specialized waste disposal. The valuable materials contained in an air conditioner can be recycled . Contact your local waste disposal center for proper disposal of an old air conditioner and contact your local authority or your dealer if you have any question. [. . . ] No reelecting is needed. (TIMER ON/OFFSLEEPSWING needs reelecting) Cautions: Note: On cooling only unit, heating mode is not available, The above information is the After replacing batteries, press ON/OFF, and display explanation of the displayed becomes as follows: information therefore varies Operation mode: AUTO, Temp. :No with those displayed in actual operation. Hints 9 Operation Cool Operation (1) Unit start Press ON/OFF button, unit starts. Previous operation status appears on display. (Not Timer setting) (2) Select operation mode Press MODE button. For each press, operation mode changes as follows: AUTO COOL DRY FAN ON/OFF TEMP Unit will run in operation mode displayed on LCD. Stop display at your desired mode. 5 1 MODE 3 3 SET (3) Select temp. o Every time the button is pressed, temp. setting increases 1 C o Every time the button is pressed, temp. setting decreases 1 C Unit will start running to reach the temp. setting on LCD. 2 FAN TIMER 4 SWING CLOCK (4) Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: AUTO LO MED HI SLEEP HEALTH LOCK RESET Air conditioner is running under displayed fan speed. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. (5) Unit stop Press ON/OFF button, the unit stops. Hints On cooling only unit, heating mode is not available. Remote controller can memorize each operation status. When starting it next time, just press ON/OFF button and unit will run in previous status. No reelecting is needed. (TIMER ON/OFFSLEEPSWING needs reelecting) 10 Operation Dry Operation (1) Unit start Press ON/OFF button, unit starts. Previous operation status appears on display. (Not Timer setting) (2) Select operation mode Press MODE button. For each press, operation mode changes as follows: AUTO COOL DRY FAN ON/OFF TEMP 5 1 MODE 3 3 SET Unit will run in operation mode displayed on LCD. Stop display at your desired mode. 2 FAN TIMER (3) Select temp. o Every time the button is pressed, temp. setting increases 1 C o Every time the button is pressed, temp. setting decreases 1 C Unit will start running to reach the temp. [. . . ] When the remote controller is manipulated, it gets the system back to the normal operation mode. 18 Maintenance For Smart Use of The Air Conditioner Setting of proper room temperature Proper temperature Do not block the air inlet or outlet Close doors and windows Use the timer effectively during operation During cooling operation prevent the penetration of direct sunlight with curtain or blind If the unit is not to be used Use the louvers effectively for a long time, turn off the power supply main switch. OFF 19 Maintenance For Smart Use of The Air Conditioner Before maintenance, be sure to turn off the system and the circuit breaker. WARNING Remote Controller Indoor Body Do not use water , wipe the controller with a dry cloth. Do not use glass cleaner or chemical cloth. Wipe the air conditioner by using a soft and dry cloth. For serious stains, use a neutral detergent diluted with water. Wring the water out of the cloth before wiping. then wipe off the detergent completely. Do not use the following for cleaning Gasoline, benzine, thinner or cleanser may damage the coating of the unit. Hot water over 40 C(104 F) may cause discoloring or deformation. O O Air Filter cleaning Remove the filter. Open the inlet grille by pulling it upward. Push up the filter's center tab slightly until it is released from the stopper, and remove the filter downward. Clean the filter. Use a vacuum cleaner to remove dust, or wash the filter with water. After washing, dry the filter completely in the shade. Attach the filter. Attach the filter correctly so that the "FRONT" indication is facing to the front. Make sure that the filter is completely fixed behind the stopper. If the right and left filters are not attached correctly, that may cause defects. Once every two weeks Close the inlet grille. 20 Maintenance Replacement of Air Purifying Filter 1. Open the lnlet Grille Prop up the inlet grille by using a small device named grille-support which located in the right side of the indoor unit. Slide the knob slightly upward to release the filter, then withdraw it. 2. Detach the standard air filter 3. Attach Air Purifying Filter Put air purifying filter appliances into the right and left filter frames. Detach old Air Purifying Filter 4. Attach the standard air filter (Necessary installation) ATTENTION: The white side of the photocatalyst air purifying filter face outside, and the black side face the unit. The green side of the bacteria-killing medium air purifying filter face outside, and the white side face the unit. 5. Close the Inlet Grille Close the Grille surely NOTE: The photocatalyst air purifying filter will be solarized in fixed time. In normal family, it will be solarized every 6 months. [. . . ]