User manual HAIER HSU-12CB13

[. . . ] The valuable materials contained in an air conditioner can be recycled . Contact your local waste disposal center for proper disposal of an old air conditioner and contact your local authority or your dealer if you have any question. Please ensure that the pipework of your air conditioner does not get damagedprior to being picked up by the relevant waste disposal center, and contribute to environmental awareness by insisting on an appropriate, anti-pollution method of disposal. Safety Instructions and Warnings Before starting the air conditioner, read the information given in the User's Guide carefully. The User's Guide contains very important observations relating to the assembly, operation and maintenance of the air conditioner. The manufacturer does not accept responsibility for any damages that may arise due to non-observation of the following instruction. [. . . ] Used to select TIMER ON, TIMER OFF, TIMER ON-OFF Used to set correct time 21. HEALTH AUTO LO MED HI Used to reset the controller back to normal condition. Used to operate the healthy function. Clock set When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows: Press CLOCK button, "AM" or "PM" flashes. Each press will increase or decrease 1min. If the button is kept depressed, time will change quickly. After time setting is confirmed, press SET, "AM "and "PM" stop flashing, while clock starts working. NOTE: Cooling only unit do not have displays and functions related with heating Hints After replacing with new batteries, remote controller will conduct self-check, displaying all information on LCD. 6 Parts and Functions Operation 1 2 5 3 ON/OFF If the unit which you purchased has not healthy function, Remote controller should like the following figure: 10 6 7 8 9 4 11 FAN 13 18 4. MODE MODE Used for unit start and stop. SWING TIMER CLOCK SET LOCK 15 20 14 12 21 19 17 13. FAN Used to select AUTO run, COOL, DRY HEAT and FAN operation Used to select fan speed LO, MED, HI, AUTO Used to set clock and timer setting. Used to select your desired temp. 18. TIMER Used to confirm timer and clock settings. 2. In DRY mode, when room temperature becomes lower than temp. setting+2oC, unit will run intermittently at LOW speed regardless of FAN setting. Power indicator on indoor unit lights up. (2)TIMER mode selection Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: ON AM OFF PM ON AM N 12:00 OFF ON PM OFF 12:00 blank 12:00 12:00 ON/OFF TIMER ON TIMER OFF TIMER ON-OFF TIMER ON-OFF FAN 1 Select your desired TIMER mode (TIMER ON or TIMER OFF), ON or OFF will flash. MODE (3)Timer setting Press HOUR / button. Every time the button is pressed, time increases 10 min. If button is kept depressed, time will change quickly. Every time the button is pressed, time decreases 10 min. If button is kept depressed, time will change quickly. It can be adjusted within 24 hours. 2 SWING TIMER 3 CLOCK 3 SET SLEEP RESET 4 LOCK (4)Confirming your setting After setting correct time, press SET button to confirm, "ON" or "OFF" stops flashing Time displayed: Unit starts or stops at x hour x min. Timer mode indicator on indoor unit lights up. To cancel TIMER mode Just press TIMER button several times until TIMER mode disappears. Hints After replacing batteries or a power failure happens, Time setting should be reset. Remote controller possesses memory function, when use TIMER mode next time, just press SET button after mode selecting if timer setting is the same as previous one. 11 Operation TIMER ON-OFF TIMER ON-OFF (1)After unit start, select your desired operation mode Operation mode will be displayed on LCD. [. . . ] setting so that room temperature won't be too Iow for your sleep. the quiet sleeping time can not be adjusted. When TIMER function is set , the quiet sleeping function can't be set up . After the sleeping function is set up, if user resets TIMER function, the sleeping function will be cancelled; the machine will be in the state of timing-on, if the two modes are set up at the same time , either of their operation time is ended first , the unit will stop automatically, and the other mode will be cancelled. Power Failure Resume Function If the unit is started for the first time, the compressor will not start running unless 3 minutes have elapsed. When the power resumes after power failure, the unit will run automatically, and 3 minutes later the compressor starts running. SLEEP operation starts SLEEP operation stops Approx. 6hrs 1 hr 1 hr Temp. setting Rises 1OC Note to the power failure resume: press the sleep button ten times in five seconds and enter this function after hearing four sounds. And press the sleep button ten times within five seconds and leave this function after hearing two sounds. Rises 1OC Unit stop In COOL, DRY mode 14 Operation Emergency operation and test operation Emergency Operation: Use this operation only when the remote controller is defective or lost, and with function of emergency running, air conditoner can run automatically for a while. [. . . ]