User manual HAIER HSU-12HF03(B)

[. . . ] The valuable materials contained in an air conditioner can be recycled. Contact your local waste disposal center for proper disposal of an old air conditioner and contact your local authority or your dealer if you have any question. Please ensure that the pipework of your air conditioner does not get damagedprior to being picked up by the relevant waste disposal center, and contribute to environmental awareness by insisting on an appropriate, anti-pollution method of disposal. All these valuable materials may be taken to a waste collecting center and used again after adequate recycling. Safety Instructions and Warnings Before starting the air conditioner, read the information given in the User's Guide carefully. [. . . ] (Don't adjust it manually. ) A beeping sound is generated when a signal from remote controller is received. Power indicator Lights up when unit starts. Timer mode indicator Lights up when Timer operation is selected. Operation mode indicator Lights up during compressor running. Actual inlet grille may vary from the one shown in the manual according to the product purchased. Outdoor Unit HSU-09C13 HSU-12HF03(B) HSU-18C13 HSU-22C13 HSU-24C13 OUTLET INLET CONNECTING PIPING AND ELECTRICAL WIRING DRAIN HOSE Air Conditioner Edition:2006/01/09 Parts and Functions Operation Buttons and display of the remote controller. 1. MODE Used to select AUTO run, COOL, DRY, HEAT and FAN operation 1 2 3 4 ON/OFF TEMP 5 6 7 8 9 10 AUTO LO MED HI 11 18 MODE SET Used for unit start and stop. 12 FAN TIMER 19 13. FAN 20 Used to select fan speed LO, MED, HI, AUTO 13 14 15 SLEEP SWING CLOCK 14. HOUR Used to set clock and timer setting. 15. SWING 21 Used to set auto fan direction. 16. SLEEP Used to select sleep mode. 16 LOCK RESET 17. LOCK Used to lock buttons and LCD display. 17 22 18. TEMP. Used to select your desired temp. 19. SET Used to confirm timer and clock settings. 20. TIMER Used to select TIMER ON, TIMER OFF, TIMER ON-OFF 21. CLOCK Used to set correct time Clock set 22. (Not Timer setting) Power indicator on indoor unit lights up. Use COOL in summer. Use HEAT in winter Use DRY in spring, autumn and in damp climate. (2) Select operation mode Press MODE button. For each press, operation mode changes as follows: ON/OFF TEMP AUTO COOL DRY HEAT FAN 6 2 FAN TIMER Unit will run in operation mode displayed on LCD. Stop display at your desired mode. 1 3 3 SET MODE (3) Select temp. o Every time the button is pressed, temp. setting increases 1 C o Every time the button is pressed, temp. setting decreases 1 C Unit will start running to reach the temp. setting on LCD. 4 SWING CLOCK 5 SLEEP (4) Fan speed selection Press FAN button. For each press, fan speed changes as follows: LOCK RESET AUTO LO MED HI COOL operation starts when room temp. setting. Ultra-low air flow Unit runs at the speed displayed on LCD. setting, unit will run intermittently at LO speed regardless of FAN setting. o Temp. setting, unit will run in mild DRY mode. Hints On cooling only unit, heating mode is not available. [. . . ] If button is kept depressed, time will change quickly. AM refers to morning and PM to afternoon ON/OFF TEMP MODE 1 3 SET 6 TIMER FAN 5 SWING 2 4 CLOCK SLEEP (4) Time confirming for TIMER ON After time setting, press TIMER button to confirm. "ON" stops blinking, While "OFF" starts blinking. Time displayed: Unit starts at x hour x min. LOCK RESET (5)Time setting for TIMER OFF Follow the same procedures in "Time setting for TIMER ON". (6) Time confirming for TIMER OFF After time setting, press SET button to confirm, "OFF" stops flashing Time displayed: Unit stops at X hour X min. To cancel TIMER mode Just press TIMER button several times until TIMER mode disappears. Air Conditioner Edition:2006/01/09 Operation Emergency operation and test operation Emergency Operation: Carry out this operation only when the remote controller is defective or lost. [. . . ]