User manual HAIER HSU-12LEK03/

[. . . ] SET / LIGHT Used to confirm timer and clock settings. Control the lightening and extinguishing of the indoor LED display board. TIMER Used to select TIMER ON, TIMER OFF, TIMER ON-OFF 21. RESET Used to reset the controller back to normal condition. HOUR / POWER/SOFT Used to set clock and timer setting. [. . . ] (1) TIMER ON Emergency operation and test operation Emergency Operation: Use this operation only when the remote controller is defective or lost. When the emergency operation switch is pressed, the" Pi "sound is heard once, which means the start of this operation. In this operation, the system automatically selects the operation modes, cooling or fan or heat, according to the room temperature. Room temperature Operation mode Designated temperature 26OC 23OC Operation mode FAN Timer mode NO NO Air flow AUTOMATIC AUTOMATIC Pi POWER/SOFT POWER/SOFT TIMER CLOCK LIGHT TIMER CLOCK LIGHT SET SLEEP SET SLEEP ABOVE 23OC COOLING POWER/SOFT TIMER CLOCK LIGHT BELOW 23OC HEAT SET SLEEP (2) TIMER OFF (Cooling only uint Room temperature BELOW 23OC Designated temperature 26OC Timer mode NO Air flow AUTOMATIC It is not possible to operate in dry mode. POWER/SOFT POWER/SOFT TIMER CLOCK LIGHT TIMER CLOCK LIGHT SET SLEEP SET SLEEP Test operation: Test operation switch is the same as emergency switch. Use this switch in the test operation when the room o temperature is below 16 C, do not use it in the normal operation. Pi Pi Continue to press the test operation switch for more than 5 seconds. After you hear the "Pi" sound twice, release your finger from the switch: the cooling operation starts with the air flow speed "Hi". (3) TIMER ON-OFF POWER/SOFT POWER/SOFT POWER/SOFT POWER/SOFT TIMER CLOCK LIGHT TIMER CLOCK LIGHT TIMER CLOCK LIGHT TIMER CLOCK LIGHT SET SLEEP SET SLEEP SET SLEEP SET SLEEP To cancel TIMER mode Just press TIMER button several times untilTIMER mode disappears. 3 Operation Comfortable SLEEP Before going to bed, you can simply press the SLEEP button and unit will operate in SLEEP mode and bring you a sound sleep. 2. In HEAT mode SLEEP Operation TIMER CLOCK LIGHT 1 hours after SLEEP mode starts, temp will become 2OC lower than temp. setting. After another 1 hours, temp decrease by 2 O C further. The unit will run for further 3 hours then stops. setting so that room temperature won't be too high for your sleep. SET SLEEP Temp. setting 1 hr 1 hr O Unit stop Decreases 2 C O Decreases 2 C 3 hrs Rises 1 C 3 hrs SLEEP SLEEP operation stops operation starts In HEAT mode O Operation Mode 1. In COOL, DRY mode 1 hours after SLEEP mode starts, temp. The unit will run for further 6 hours then stops Temp. setting so that room temperature won't be too Iow for your sleep. SLEEP operation stops SLEEP operation starts Approx. 6hrs 3. In AUTO mode The unit operates in corresponding sleep mode corresponding sleep mode adapted to the automatically selected operation mode. In FAN mode It has no SLEEP function. 5. When quiet sleeping function is set to 8 hours the quiet sleeping time can not be adjusted. When TIMER function is set, the quiet sleeping function can't be set up. After the sleeping function is set up, if user resets TIMER function, the sleeping function will be cancelled; the machine will be in the state of timing-on, if the two modes are set up at the same time, either of their operation time is ended first , the unit will stop automatically, and the other mode will be cancelled. 1 hr 1 hr Rises 1 C O O Rises1 C Unit stop Temp. setting In COOL, DRY mode Power Failure Resume Function If the unit is started for the first time, the compressor will not start running unless 3 minutes have elapsed. When the power resumes after power failure, the unit will run automatically, and 3 minutes later the compressor starts running. Note to the power failure resume: press the sleep button ten times in five seconds and enter function after hearing four sounds. And press the sleep button ten times within five seconds and leave this function after hearing two sounds. 4 Maintenance For Smart Use of The Air Conditioner Setting of proper room temperature Proper temperature Do not block the air inlet or outlet Remote Controller Indoor Body Do not use water wipe the controller with a dry cloth. Do not use glass cleaner or chemical cloth. Wipe the air conditioner by using a soft and dry cloth. For serious stains, use a neutral detergent diluted with water. Wring the water out of the cloth before wiping. then wipe off the detergent completely. Do not use the following for cleaning Close doors and windows Use the timer effectively during operation During cooling operation prevent the penetration of direct sunlight with curtain or blind Gasoline, benzine, thinner or cleanser may damage the coating of the unit. Hot water over 40 C(104 F) may cause discoloring or deformation. O O Air Filter cleaning Open the inlet grille by pulling it upward. Use an exclusive power source with a circuit breaker Check proper installation of the drainage securely STRICT ENFORCEMENT OFF Connect power supply cord to the outlet completely STRICT ENFORCEMENT Use the proper voltage STRICT STRICT ENFORCEMENT ENFORCEMENT Do not use power supply Take care not to damage the power supply cord. cord in a bundle. 1. Do not use power supply cord extended or connected in halfway 2. Do not install in the place where there is any possibility of inflammable gas leakage around the unit. 3. Do not get the unit exposed to vapor or oil steam. PROHIBITION Do not insert objects into the air inlet or outlet. PROHIBITION Do not start or stop the operation by disconnecting the power supply cord and so on. PROHIBITION Do not channel the air flow directly at people, especially at infants or the aged. Do not try to repair or reconstruct by yourself. PROHIBITION Connect the earth cable. PROHIBITION earthing PROHIBITION CAUTION Do not use for the purpose of storage of Take fresh air occasionally especially Do not operate the switch with food, art work, precise equipment, when gas appliance is running at the wet hand. [. . . ] 4. The distance between the indoor unit and the floor should be more than 2m. 5. The wiring method should be in line with the local wiring standard. After installation, the power plug should be easily reached. . 7. The used batteries should be disposed of properly. [. . . ]