User manual HAIER HW-07HA03

[. . . ] Do not insert sticks, fingers or other objects into the unit. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person. After installation, the power plug should be easily reached. [. . . ] The wiring method should be in line with the local wiring standard. OPERATION CONDITIONS Applicable ambient temperature range: Cooling Max. Temperture: Min. Temperture: Indoor D. B 32 C 18 C o o Outdoor D. B 43 C 18 C o o Note: o W. B 23 C 14 C o o W. B 26 C / D. B :Dry Bulb Temperature W. B :Wet Bulb Temperature It is advisable not to keep horizontal flap at downward position for a long time in COOLor FAN mode, otherwise , condensate water might occur. Don't move the vertical flap with hand in order to avoid the vertical flap abnormal, using the AUTO SWING switch to adjust the move of vertical flap. 2 AIR CONDITIONER OPERATION PART INDENTIFICATION Machine body Air outlet (indoor side) Machine body Front panel Air inlet (indoor side) CLOSE OPEN 13 24 3 CARE AND MAINTENANCE Always turn off the air conditioner and the main power supply before clean the unit. Switch off the power supply if the unit is not going to be used for a long period of time. 1 Ventilation 1 Air filter cleaning It is advisable to clean air filter every two weeks for longer operation. (You will find how to clean the filter on page 2 . ) Cleaning of the air filter 2 Notes Avoid opening doors and windows unless necessary. Don't be exposed to cold air for a long time. a little bit higher before going to bed. Air filter (inside) Operation panel Ventilation Power plug Air inlet (outdoor side) The ventilation lever must be CLOSE position in order to maintain the best cooling conditions. When fresh air is necessary in the room, set the ventilation lever to the OPEN position. The damper is opened and room air is exhausted. Proper temperature 2 Air filter cleaning When dirt accumulates on air filter, air circulation will be blocked, which causes poor cooling. 3). >500mm INSTALLATION PROCEDURES 1. Fix the prefabricated iron frame to stable position by expansible screws. Put the whole machine with all the accessories installed, on the iron frame. If there's water outlet flexible pipe, lead it to needed position(see Fig. 1). Wall cover support fig. 1 Water outlet flexible pipe(provide by user) Fig. 1 5-10mm 3. Fill any distance between the wall hole and the machine body with flexible sponge rubber strip to prevent the entering of outer noise and the leaking of the coolness. 4. After installation of the conditioner, insert the power plug into the outlet and perform test-run. fig. 2 fig. 3 Cautions NOTES: For longer and trouble-free operation of the unit, pay special attention to the following: Install air-con at a place strong enough to support the unit. Leave enough space around air inlet and outlet for better circulation. Problems may occur if unit is installed in the following places: Place where oil exists in the air including engine oil or seaside with salt breeze blows and hot spring area with sulphurous gas in the air. Power cord: Be sure to use the exclusive power cord. [. . . ] Problems may occur if unit is installed in the following places: Place where oil exists in the air including engine oil or seaside with salt breeze blows and hot spring area with sulphurous gas in the air. Power cord: Be sure to use the exclusive power cord. Change installation place: If air-con need to be changed to another place please contact the dealer, who sold you the unit. Always use at the rated voltage and with specfic air conditioning circuit THE ENCLOSED ACCESSORIES OF THE CONDITIONER Name Rubber lid Manual Drain pan Sealed gasket Screw Figure Quantity 1 1 1 1 4 5 TROUBLESHOOTING 57 68 Before calling for service. Check the following points before calling for repairs or service. PREPARATIONS BEFORE INSTALLATION Make the wall hole or window hole (see Fig. 1) Iron frame MODEL HW07M HW09M HW12M A 370mm 395mm 440mm B 485mm A Phenomenon B Cause or check points Solution 615mm 635mm Width of the wall HW18M Fig. [. . . ]