User manual HAIER HW-09LF03

[. . . ] If the supply cord is damaged, it must be replaced by the manufacturer or its serviceagent or a similar qualified person. After installation, the power plug should be easily reached. The wiring method should be in line with the local wiring standard. 2 Parts Name Machine body Front panel Air inlet (indoor side) Machine body Air outlet (indoor side) Air inlet (outdoor side) Display panel Power plug Air filter (inside) Operation panel 3 Operation Guide Auto swing switch When the switch is set to " ", the indicator lights up, and vertical louvers will swing from side to side, delivering gentle air thus making you feel very comfortable. When it is set to " ", the indicator goes out, and the vertical louvers stop at any position. Mode selection switch Mode selection switch controls the fan motor speed and cooling speed. <1> When set to " <2> When set to " ", fan motor runs at high speed to blow out strong air. [. . . ] To obtain better cleaning effect, soap water or neutral detergent may be used. Flush air filter carefully with clean water after removing dirt. Let it dry completely. Cleaning of the air filter 6 Maintenance Disposal of the condensed water Generally there are two methods available on disposal of the condensed water: 1. Block the bottom plate hole of the conditioner with rubber lid, install outlet pipe fitting on the back hole and let the condensing water flow from the back hole of the conditioner. (See Fig. 1 ) In this method, the accumulated condensed water in the bottom plate is hit by the fan onto the heat exchanger, and evaporated and blown out from the machine. It can cool the heat exchanger radiator more quickly, and improve the energy efficiency of the conditioner. But the hitting noise by the fan at the outdoor side is relatively large. Block the back hole of the conditioner with rubber lid and install outlet pipe fitting to the bottom hole, which can make the condensed water flow out from the bottom plate. (See Fig. 2) If necessary the above two methods can both have extra pipe added on the outlet pipe fitting. (available on the market). (Refer to P12 for choosing these two modes. ) Fig. 1 Fig. 2 Outlet pipe fitting Rubber lid Back hole Rubber lid Bottom plate hole Back hole Outlet pipe fitting Bottom plate hole Cautions Power cord: Be sure to use the exclusive power cord. Change installation place: If air-con need to be changed to another place please contact the dealer, who sold you the unit. 7 Maintenance Avoid opening doors and windows unless necessary. Don't be exposed to cold air for a long time. Use curtain or blind Direct sunlight may reduce cooling effect, always use window curtain. Keep heat source away from air conditioner. Set temp . a little bit higher before going to bed. After unit stops, don't restart it until 3 min. have elapsed. Proper temperature OK!Enjoy a 3-min nap 8 Troubleshooting Readjust power supply. Replace fuse. Doesn't work Is plug firmly inserted?Readjust the thermostat. Does fuse get burned? Use curtain or blind. Is thermostat switch wrongly adjusted? No cool air or poor cooling Shut doors and windows. Is there any direct sunlight in the room?Are there any obstacles blocking air inlet and outlet? Is air filter clogged?Remove the heat source Is there too much heat source in the room?If problems can not be solved please pull out power plug and contact your dealer. 9 Installation Instructions Don't hang clothes in the vicinity of air inlet. This will decrease cooling effect and cause abnormal operation. Temperature should be set properly when there are infant, child, the aged or disabled in the room. Go away! Baby has gone sleep, better to adjust suitable temp. Before operating mode selection switch, check that if the air inlet or outlet have been blocked. For longer and trouble-free operation of the unit, pay special attention to the following: Install air-con at a place strong enough to support the unit. [. . . ] Cooling-only type air-conditioner: before dispatched from the factory, the drip hole at the bottom plate has been blocked by rubber lid in the accessories. If the surrounding humidity is high, should assemble drainage bend in the drainage hole at the back of bottom plate and connect the drainage tube as Rubber lid illustrated in Fig. If the user doesn't need to Drain pan retain the condensate in the bottom plate, can Screw remove the rubber lid on the bottom and as illustrated in Fig. 2 pan on the bottom of the air-conditioner, and connect drainage tube at the water outlet hole on the drain pan. Condenser 5. [. . . ]