User manual HAIER HW-18LM13

[. . . ] ROOM AIR CONDITIONER 4 AIR CONDITIONER INSTALLATION (ONLY FOR REFERANCE) SELECTION OF THE INSTALLATION POSITION 1, The air-conditioner is better installed in shadow or in a place with short period of sunshine. In case the air-conditioner is installed at the point exposed directly to the sunshine, it should be protected from the direct sunlight as possible in order to avoid the long time of direct sunlight otherwise its performance will be lowered. [. . . ] If there's water outlet flexible pipe, lead it to needed position(see Fig. 1). cover Wall support fig. 1 Water outlet flexible pipe(provide by user) Fig. 1 3. Fill any distance between the wall hole and the machine body with flexible sponge rubber strip to prevent the entering of outer noise and the leaking of the coolness. After installation of the conditioner, insert the power plug into the outlet and perform test-run. >500mm 5-10mm fig. 2 fig. 3 Cautions NOTES: For longer and trouble-free operation of the unit, pay special attention to the following: Install air-con at a place strong enough to support the unit. Leave enough space around air inlet and outlet for better circulation. Problems may occur if unit is installed in the following places: Place where oil exists in the air including engine oil or seaside with salt breeze blows and hot spring area with sulphurous gas in the air. Power cord: Be sure to use the exclusive power cord. Change installation place: If air-con need to be changed to another place please contact the dealer, who sold you the unit. Always use at the rated voltage and with specfic air conditioning circuit THE ENCLOSED ACCESSORIES OF THE CONDITIONER Name Rubber lid Outlet pipe fitting Manual Sealed gasket Figure HW-07LM03 HW-07LM13 HW-09LM03 HW-09LM13 HW-12LM03 HW-12LM13 HW-18LM13 HW-18LM03(T3) HW-24LM03(T3) HW-18LM13(T3) HW-24LM13(T3) HW-12LM03(T3) 1 1 1 1 1 3 5 TROUBLESHOOTING Before calling for service. Check the following points before calling for repairs or service. 1 1 1 1 PREPARATIONS BEFORE INSTALLATION Make the wall hole or window hole (see Fig. 1) 57 68 Phenomenon Cause or check points Solution MODEL HW-07LM03 HW-09LM03 HW-07LM13 HW-09LM13 A 370mm 395mm B Iron frame 485mm A HW-12LM03 HW-12LM13 HW-12LM03(T3) HW-18LM03(T3) HW-24LM03(T3) HW-18LM13(T3) HW-24LM13(T3) HW-18LM13 615mm Switch on the machine but it does not work immediately. If the machine is started after stop, it will need about 3 minutes to re-start so as to prevent the fuse from break. B 440mm 635mm Width of the wall Fig. 1 Switch on the machine but it does not work. Is plug firmly inserted?Is there power failure? Readjust power supply Prepare unit for installation: 1. Take out the conditioner and accessories from the package . 2. Choose one way from below two options on disposal of the condensed water. Generally there are two methods available on disposal of the condensed water: Does fuse get burned? Replace fuse. Method 1 Block the bottom plate hole of the conditioner with rubber lid, install outlet pipe fitting on the back hole and let the condensing water flow from the back hole of the conditioner. [. . . ] (See Fig. 2) Fig. 2 Rubber lid Are there any obstacles blocking air inlet and outlet? Remove the obstacles. Clean it. Is air filter clogged? Outlet pipe fitting Bottom plate hole If necessary the above two methods can both have extra pipe added on the outlet pipe fitting (available on the market). Is there too much heat source in the room? Remove the heat source NOTE:For some model the air conditioner is designed to splash the condensed water on the heat exchanger for maximun cooling efficiency, the extra condensed water will be blown out from the machine , But the hitting noise by the fan at the outdoor side is relatively. (See Fig. 3) Fig. 3 If problems can not be solved please pull out power plug and contact your dealer. Bottom plate [. . . ]